1 D+H Mechatronic (english) 1.1 SHEV controllers General Preliminary Remarks about SHEV controllers To ensure smoke extraction in case of fire, an electric smoke and heat exhaust system (SHEV) is provided. The smoke and heat exhaust ventilators mounted on site (skylight windows, roof windows or the like) are controlled using one or more SHEV control panels. In addition, the system can be used for daily ventilation using a ventilation button.   The SHEV system consists primarily of the following system components:   - SHEV control panel - Power supply charger unit - Battery emergency power supply - Electrical drives with electronic limit stop and overload cut-off - SHEV trigger button - Ventilation button - Electronic fire detectors   The various system parts are put together individually depending on the system size or specific requirements. The power supply charger unit is equipped with an emergency power supply that keeps the system ready to operate for at least 72 hours in the event of a power cut. The calculation of the unit prices described in the following must include the delivery and installation with the associated small hardware and fasteners, including commissioning.   System description   The SHEV openings are opened immediately after triggering the fire alarm control unit or smoke vent buttons. The applicable regulations, such as VDE 0833, VDE 0100, DIN 18232, VdS 2221, LBO (German Federal State Building Law), Guidelines for power-operated windows, doors and gates, the Machinery Directive DIN EN 14351-1, the provisions of the local fire brigade and, in particular, DIN 18232-2 and DIN EN 12101 Part 2, 9 and 10 must be observed. The proper dimensioning, installation and commissioning of smoke and heat exhaust systems, systems and devices for smoke exhaust or air intake wings for supporting the smoke and heat exhaust ventilation must be carried out by a qualified SHEV specialist company. Proof must be provided of valid approval as a specialist SHEV installer and a certified quality management system in accordance with DIN EN ISO 9001 for the scope of validity of the services offered. The SHEV control panel consists of an electric control unit in accordance with VdS 2581 with integrated energy supply unit in accordance with VdS 2593. A SHEV retriggering function and smoke detector remote reset must be included. It must be possible to connect at least 8 SHEV operation panels and 14 fire detectors. Control panel controlled via microprocessor for automatic closing after 2 - 45 minutes and continuously adjustable ventilation stroke limiter. Internal fault diagnostic displays, automatic emergency closing function in ventilation mode in case of mains outage. Control board with slot for additional functional enhancements. It should be possible to connect rain detectors or wind/rain sensors without additional modules. Encoding option for various SHEV and ventilation functions. The SHEV control panel must be equipped with a compact housing with locking sheet steel door. The SHEV openings serve as openings for smoke and hot air to escape in case of fire. The cable routing and delivery, as well as the installation of the power-operated window elements or skylights, are carried out on site. Information CPS-M1-S SHEV control panel based on AdComNet   The CPS-M is not only the first control panel that has the ability to communicate with other CPS-M control panels and other AdComNet-enabled products, but also the first product that is based directly on AdComNet. All parameterisation, function settings and assignment of lines and groups are set using the "SCS" (Service & Configuration Suite) operating software. 1.1.1 SHEV control panel - modular - CPS-M1-020-0202-B 24 V DC / 20 A / 2 RM/RT-lines / 2 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 1x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0202-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.12 1.1.2 SHEV control panel - modular - CPS-M1-020-0202-B-WD 24 V DC / 20 A / 2 RM/RT-lines / 2 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 1x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0202-B-WD   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.13 1.1.3 SHEV control panel - modular - CPS-M1-020-0204-B 24 V DC / 20 A / 2 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0204-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.17 1.1.4 SHEV control panel - modular - CPS-M1-020-0204-B-WD 24 V DC / 20 A / 2 RM/RT-lines / 4 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0204-B-WD   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.18 1.1.5 SHEV control panel - modular - CPS-M1-020-0404-B 24 V DC / 20 A / 4 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0404-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.22 1.1.6 SHEV control panel - modular - CPS-M1-020-0404-B-WD 24 V DC / 20 A / 4 RM/RT-lines / 4 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0404-B-WD   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.23 1.1.7 SHEV control panel - modular - CPS-M1-020-0606-B 24 V DC / 20 A / 6 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module basic - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0606-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.27 1.1.8 SHEV control panel - modular - CPS-M1-020-0606-B-WD 24 V DC / 20 A / 6 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module basic - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0606-B-WD   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.28 1.1.9 SHEV control panel - modular - CPS-M1-040-0204-B 24 V DC / 40 A / 2 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0204-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.32 1.1.10 SHEV control panel - modular - CPS-M1-040-0204-B-WD 24 V DC / 40 A / 2 RM/RT-lines / 4 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0204-B-WD   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.33 1.1.11 SHEV control panel - modular - CPS-M1-040-0206-B 24 V DC / 40 A / 2 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0206-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.37 1.1.12 SHEV control panel - modular - CPS-M1-040-0206-B-WD 24 V DC / 40 A / 2 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0206-B-WD   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.38 1.1.13 SHEV control panel - modular - CPS-M1-040-0404-B 24 V DC / 40 A / 4 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0404-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.14 SHEV control panel - modular - CPS-M1-040-0406-B 24 V DC / 40 A / 4 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0406-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.15 SHEV control panel - modular - CPS-M1-040-0606-B 24 V DC / 40 A / 6 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module basic - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0606-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.52 1.1.16 SHEV control panel - modular - CPS-M1-040-0606-B-WD 24 V DC / 40 A / 6 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module basic - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0606-B-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.17 SHEV control panel - modular - CPS-M1-060-0206-B 24 V DC / 60 A / 2 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 3x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0206-B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.57 1.1.18 SHEV control panel - modular - CPS-M1-060-0206-B-WD 24 V DC / 60 A / 2 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 3x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0206-B-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.19 SHEV control panel - modular - CPS-M1-060-0208-B 24 V DC / 60 A / 2 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9.Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0208-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.20 SHEV control panel - modular - CPS-M1-060-0210-B 24 V DC / 60 A / 2 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0210-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.21 SHEV control panel - modular - CPS-M1-060-0406-B 24 V DC / 60 A / 4 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 3x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0406-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.22 SHEV control panel - modular - CPS-M1-060-0408-B 24 V DC / 60 A / 4 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0408-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.23 SHEV control panel - modular - CPS-M1-060-0410-B 24 V DC / 60 A / 4 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0410-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.24 SHEV control panel - modular - CPS-M1-060-0410-B-WD 24 V DC / 60 A / 4 RM/RT-lines / 10 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0410-B-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.25 SHEV control panel - modular - CPS-M1-080-0208-B 24 V DC / 80 A / 2 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0208-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.26 SHEV control panel - modular - CPS-M1-080-0210-B 24 V DC / 80 A / 2 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0210-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.27 SHEV control panel - modular - CPS-M1-080-0216-B 24 V DC / 80 A / 2 RM/RT-lines / 16 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 8x actuator module basic - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0216-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.28 SHEV control panel - modular - CPS-M1-080-0408-B 24 V DC / 80 A / 4 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0408-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.29 SHEV control panel - modular - CPS-M1-080-0410-B 24 V DC / 80 A / 4 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0410-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.30 SHEV control panel - modular - CPS-M1-080-0410-B-WD 24 V DC / 80 A / 4 RM/RT-lines / 10 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0410-B-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.31 SHEV control panel - modular - CPS-M1-080-0608-B 24 V DC / 80 A / 6 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module basic - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0608-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.32 SHEV control panel - modular - CPS-M1-080-0610-B 24 V DC / 80 A / 6 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0610-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.33 SHEV control panel - modular - CPS-M1-080-0808-B 24 V DC / 80 A / 8 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module basic - 4x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0808-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.34 SHEV control panel - modular - CPS-M1-080-0810-B 24 V DC / 80 A / 8 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 4x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0810-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.35 SHEV control panel - modular - CPS-M1-080-1010-B 24 V DC / 80 A / 10 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Pole reversing drives can be connected to one actuator module basic in two groups of 10 amps each. Each actuator module basic has 4 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module basic can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module basic - 5x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-1010-B   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.36 SHEV control panel - modular - CPS-M1-020-0202 24 V DC / 20 A / 2 RM/RT-lines / 2 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 1x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0202   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.37 SHEV control panel - modular - CPS-M1-020-0202-WD 24 V DC / 20 A / 2 RM/RT-lines / 2 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 1x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0202-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.38 SHEV control panel - modular - CPS-M1-020-0204 24 V DC / 20 A / 2 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0204   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.39 SHEV control panel - modular - CPS-M1-020-0204-WD 24 V DC / 20 A / 2 RM/RT-lines / 4 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0204-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.40 SHEV control panel - modular - CPS-M1-020-0404 24 V DC / 20 A / 4 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0404   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.41 SHEV control panel - modular - CPS-M1-020-0404-WD 24 V DC / 20 A / 4 RM/RT-lines / 4 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0404-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.42 SHEV control panel - modular - CPS-M1-020-0606 24 V DC / 20 A / 6 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0606   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.43 SHEV control panel - modular - CPS-M1-020-0606-WD 24 V DC / 20 A / 6 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-020-0606-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.44 SHEV control panel - modular - CPS-M1-040-0204 24 V DC / 40 A / 2 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0204   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.45 SHEV control panel - modular - CPS-M1-040-0204-WD 24 V DC / 40 A / 2 RM/RT-lines / 4 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0204-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.46 SHEV control panel - modular - CPS-M1-040-0206 24 V DC / 40 A / 2 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0206   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.47 SHEV control panel - modular - CPS-M1-040-0206-WD 24 V DC / 40 A / 2 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0206-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.48 SHEV control panel - modular - CPS-M1-040-0404 24 V DC / 40 A / 4 RM/RT-lines / 4 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0404   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.49 SHEV control panel - modular - CPS-M1-040-0406 24 V DC / 40 A / 4 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0406   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.50 SHEV control panel - modular - CPS-M1-040-0606 24 V DC / 40 A / 6 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0606   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.51 SHEV control panel - modular - CPS-M1-040-0606-WD 24 V DC / 40 A / 6 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-040-0606-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.52 SHEV control panel - modular - CPS-M1-060-0206 24 V DC / 60 A / 2 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 3x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0206   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.53 SHEV control panel - modular - CPS-M1-060-0206-WD 24 V DC / 60 A / 2 RM/RT-lines / 6 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 3x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0206-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.54 SHEV control panel - modular - CPS-M1-060-0208 24 V DC / 60 A / 2 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0208   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.55 SHEV control panel - modular - CPS-M1-060-0210 24 V DC / 60 A / 2 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0210   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.56 SHEV control panel - modular - CPS-M1-060-0406 24 V DC / 60 A / 4 RM/RT-lines / 6 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 3x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0406   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.57 SHEV control panel - modular - CPS-M1-060-0408 24 V DC / 60 A / 4 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0408   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.58 SHEV control panel - modular - CPS-M1-060-0410 24 V DC / 60 A / 4 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0410   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.59 SHEV control panel - modular - CPS-M1-060-0410-WD 24 V DC / 60 A / 4 RM/RT-lines / 10 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 600 x 800 x 260 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-060-0410-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.60 SHEV control panel - modular - CPS-M1-080-0208 24 V DC / 80 A / 2 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0208   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.61 SHEV control panel - modular - CPS-M1-080-0210 24 V DC / 80 A / 2 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0210   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.62 SHEV control panel - modular - CPS-M1-080-0216 24 V DC / 80 A / 2 RM/RT-lines / 16 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 8x actuator module - 1x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0216   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.63 SHEV control panel - modular - CPS-M1-080-0408 24 V DC / 80 A / 4 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0408   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.64 SHEV control panel - modular - CPS-M1-080-0410 24 V DC / 80 A / 4 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0410   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.65 SHEV control panel - modular - CPS-M1-080-0410-WD 24 V DC / 80 A / 4 RM/RT-lines / 10 motor groups without touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 2x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0410-WD   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.66 SHEV control panel - modular - CPS-M1-080-0608 24 V DC / 80 A / 6 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0608   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.67 SHEV control panel - modular - CPS-M1-080-0610 24 V DC / 80 A / 6 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 3x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0610   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.68 SHEV control panel - modular - CPS-M1-080-0808 24 V DC / 80 A / 8 RM/RT-lines / 8 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 4x actuator module - 4x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0808   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.69 SHEV control panel - modular - CPS-M1-080-0810 24 V DC / 80 A / 8 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 4x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-0810   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.70 SHEV control panel - modular - CPS-M1-080-1010 24 V DC / 80 A / 10 RM/RT-lines / 10 motor groups with touch panel   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Functions and dependencies can be individually parameterised via the D+H software SCS. Further CPS-M control panels can be networked with each other via the integrated AdComNet interface. The 3.5-inch touch panel enables status display for all modules of the respective CPS-M control panel, a reset and deactivation of individual lines as well as changing the menu language between German and English. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 20 SHEV operation panels and 60 fire detectors can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module - 5x trigger module   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 800 x 1000 x 300 mm   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-080-1010   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.71 SHEV control panel - modular - CPS-M1 - freely configurable 24 V DC / Special production according to customer requirements   Performance features: The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9; Variable modular technology for complex position requirements; Flexible system design with any combination of functional modules; Installation on 35 mm supporting rail system; Expandable with up to 30 CPS-M function modules incl. CM module;   Possible function module: - Controller module - CM-BT1-D4-P2 - Supply module - PSM-1-24-40 - Actuator module 24 V DC - AM-1-2-10-24-D6-D2 - Actuator module 230 V AC - AM-1-1-08-230-D4-D2 - Trigger module - TMA-1-D4-D12 - Bistable relay module - BRM-1-COC-0006 - Input output module digital - IOM-D1-1212 - Input output module analogue & digital- ADM-AD1-1212-4   Possible bus communication: - KNX and Modbus via the D+H KNX Modbus RTU Gateway and ACN-GW501-MRTU AdComNet Modbus gateway   Can be expanded via the AdComNet interface with further CM modules and AdComNet enabled devices from D+H; Addition of the drive current in 20 A steps; Max. 10 A drive current per 24 V DC group; Connection of up to 10 SHEV operation panels or 30 fire detectors per line (Only detectors permitted by D+H may be used); Integrated comfort functions for daily ventilation: - Storage/key operation; - OPEN running time limit - Ventilation time limitation   Integrated protection functions: - Weather signal = CLOSED control - Mains outage = CLOSED control   Components can be retrofitted in case of building modifications;   Switchable SHEV safety functions: - Fault equal to alarm - SHEV retriggering function and smoke detector remote reset - Alarm = CLOSED control   Technical data: Supply: 230 V AC / 50 Hz Output: 24 V DC Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035)   Scope of supply: Control panel in lockable surface-type housing, touch panel, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-S   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.00 1.1.72 Basic / expansion set - CM-PSM-MSQ-TP-BTM-TCSU-CC for modular SHEV control panel CPS-M   Performance features: AdComNet bus system for seamless networking of the modules within the CPS-M and further D+H AdComNet components. Makes it possible to provide the CPS-M with an initial source of load current up to 40 A and to charge a 26 Ah set of batteries. Can be expanded with connectors integrated into the module base. Installation via the module socket on 35 mm top hat rail.   Consisting of the CPS-M modules: - controller module - supply module - module socket 4 times - pouch panel 3,5" - bus termination module - temperature control sensor unit - connecting 1 m and 2 m   Brand: D+H Mechatronic AG Type: CM-PSM-MSQ-TP-BTM-TCSU-CC   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.704.01 1.1.73 Basic / expansion set - CM-B-PSM-MSQ-TP-BTM-TCSU-CC for modular SHEV control panel CPS-M   Performance features: Makes it possible to provide the CPS-M with an initial source of load current up to 40 A and to charge a 26 Ah set of batteries. Can be expanded with connectors integrated into the module base. Installation via the module socket on 35 mm top hat rail.   Consisting of the CPS-M modules: - controller module-basic - supply module - module socket 4 times - pouch panel 3,5" - bus termination module - temperature control sensor unit - connecting 1 m and 2 m   Brand: D+H Mechatronic AG Type: CM-B-PSM-MSQ-TP-BTM-TCSU-CC   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.704.02 1.1.74 Basic / expansion set - CM-PSM-MSQ-BTM-TCSU-CC for modular SHEV control panel CPS-M   Performance features: AdComNet bus system for seamless networking of the modules within the CPS-M and further D+H AdComNet components. Makes it possible to provide the CPS-M with an initial source of load current up to 40 A and to charge a 26 Ah set of batteries. Can be expanded with connectors integrated into the module base. Installation via the module socket on 35 mm top hat rail.   Consisting of the CPS-M modules: - controller module - supply module - module socket 4 times - bus termination module - temperature control sensor unit - connecting 1 m and 2 m   Brand: D+H Mechatronic AG Type: CM-PSM-MSQ-BTM-TCSU-CC   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.704.41 1.1.75 Basic / expansion set - CM-B-PSM-MSQ-BTM-TCSU-CC for modular SHEV control panel CPS-M   Performance features: Makes it possible to provide the CPS-M with an initial source of load current up to 40 A and to charge a 26 Ah set of batteries. Can be expanded with connectors integrated into the module base. Installation via the module socket on 35 mm top hat rail.   Consisting of the CPS-M modules: - controller module-basic - supply module - module socket 4 times - bus termination module - temperature control sensor unit - connecting 1 m and 2 m   Brand: D+H Mechatronic AG Type: CM-B-PSM-MSQ-BTM-TCSU-CC   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.704.42 1.1.76 Supply expansionset - PSM-MS-TCSU-CC for modular SHEV control panel CPS-M   Performance features: Enables additional supply of an existing CPS-M controller with up to 40 A. Can be expanded with connectors integrated into the module bases. Installation via the module socket on 35 mm top hat rail.   Performance features Consisting of the CPS-M modules: - supply module - supply module socket - temperature control sensor unit - connecting cable 2 m   Brand: D+H Mechatronic AG Type: PSM-MS-TCSU-CC   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.704.10 1.1.77 Controller module - CM-BT1-D4-P2 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The CPS-M control module is primarily responsible for communication of the control panel via AdComNet (Advanced Communication Network). Each system requires just one controller module to ensure that the control panel is fully functional, communicate via AdComNet and configure the connected modules, operation elements and drives. In addition, the corresponding ACN interface can be used to establish a connection to additional CPS-M control panels, creating one large, single network. A service technician can use a USB interface on the front and SCS software to configure the system and the connected ACB drives. The controller module features 2 isolated change over contacts that can be used to output system statuses such as faults, alarms, etc. In addition, 3 digital inputs evaluate the status of operation elements such as buttons, switches, etc. The module sockets enable standardised installation on a 35 mm top hat rail and the supply and bus connection via integrated plug connectors. This ensures that it is easy to expand the controller. The use of spring-type terminals on the controller module also makes installation fast for the service technician. The integrated touch panel can be used to query the status of individual modules and carry out their basic functions. There are LEDs on the front of the controller module that can quickly detect the current system status on site. These LEDs indicate the system and alarm state of the system and the module.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Digital inputs Number: 3 Switching type: minus or plus aktive Voltage range: ±30 V DC Assignment: Configurable Cross section: max. 1.5 mm² flexible   Isolated contacts Number: 2 Design: Changeover contact Assignment: Configurable Cross section: max. 1.5 mm² flexible Switching voltage: max. 35 V DC Switching current: max. 1 A   Display connection Interface: R12   AdComNet connection Cross section: max. 1.5 mm² flexible   Maintenance port: USB interface   Operation display:: LED - green Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: CM-BT1-D4-P2   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.702.10 1.1.78 Controller module - CM-B-1-D4-P2 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The CPS-M control module is the mail module for every configuration. Each system requires just one controller module to ensure that the control panel is fully functional and to configure the connected modules, operation elements and drives. A service technician can use a USB interface on the front and SCS software to configure the system and the connected ACB drives. The controller module features 2 isolated change over contacts that can be used to output system statuses such as faults, alarms, etc. In addition, 3 digital inputs evaluate the status of operation elements such as buttons, switches, etc. The module sockets enable standardised installation on a 35 mm top hat rail and the supply and bus connection via integrated plug connectors. This ensures that it is easy to expand the controller. The use of spring-type terminals on the controller module also makes installation fast for the service technician. The integrated touch panel can be used to query the status of individual modules and carry out their basic functions. There are LEDs on the front of the controller module that can quickly detect the current system status on site. These LEDs indicate the system and alarm state of the system and the module.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Digital inputs Number: 3 Switching type: minus or plus active Voltage range: ±30 V DC Assignment: Configurable Cross section: max. 1.5 mm² flexible   Isolated contacts Number: 2 Design: Changeover contact Assignment: Configurable Cross section: max. 1.5 mm² flexible Switching voltage: max. 35 V DC Switching current: max. 1 A   Display connection Interface: R12   Maintenance port: USB interface   Operation display:: LED - green Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: CM-BT1-D4-P2   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.702.94 1.1.79 Supply module - PSM-1-24-40 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The power supply module is responsible for properly supplying power to the control panel system. Each PSM module used can supply up to 40 A to the control panel system and ensure a reliable supply of emergency power in the event of a mains outage through automatic switching from the power pack to the battery. The temperature-controlled battery charge provided by the temperature sensor and integrated protection against excessive discharge monitors and controls the charging process for the emergency power batteries. This substantially reduces the service life of the system and the likelihood that it will fail. There are LEDs on the front of the trigger module that can quickly detect the current system status on site. These LEDs indicate the system and alarm state of the system and the module. The module sockets enable standardised installation on a 35 mm top hat rail and the supply and bus connection via integrated plug connectors. This ensures that it is easy to expand the controller. The use of spring-type terminals on the power supply module also makes installation fast for the service technician.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Connection for power supply Cross section: max. 6 mm² flexible   External connection for peripherals Cross section: max. 2.5 mm² flexible   Connection temperature sensor Interface: R12   Barrery connectionu Cross section: max. 6 mm² flexible Supply: max. 2x Akku Typ 6 Protection against excessive discharge: YES Temperature monitoring: YES   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: PSM-1-24-40   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.702.00 1.1.80 Actuator module 24 V DC - AM-1-2-10-24-D6-D2 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The CPS-M actuator module is used to connect motorised 24 V DC drives to the control panel system. Each actuator module has two motor connections on it, each of which generates an output current of 10 A. Thanks to the monitoring system being used, the drives can be monitored for a wire break, short circuit and overload. When connecting ACB-compatible drives, the SCS tool can be used to change their stroke or running speeds. The actuator module also features 2 digital outputs and 4 digital inputs that can be configured in the SCS tool. In this tool, users can connect buttons, switches or indicator lights to perform functions such as activating drives or displaying system statuses. There are LEDs on the front of the actuator module that can quickly detect the current system status on site. These LEDs indicate the system and alarm state of the system and the module. Suitable module sockets enable standardised installation on a 35 mm top hat rail and the supply and bus connection via integrated plug connectors. This ensures that it is easy to expand the controller. The use of spring-type terminals on the actuator module also makes installation fast for the service technician.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Monitored motor outputs Number: 2 Output voltage: 24 V DC Output current per connection: max. 10 A Ausgangsstrom gesamt: max. 20 A Cross section: max. 2.5 mm² flexible Usable drives: Polarity-changing drives, ACB-compatible drives Fuse protection: electronic   Digital inputs Number: 4 Switching type: minus or plus active Voltage range: ±30 V DC Assignment: configurable Cross section: max. 1.5 mm² flexible   Digital outputs Number: 2 Output current: max. 50 mA Output voltage: 24 V DC short-circuit resistant Assignment: Configurable Cross section: max. 1.5 mm² flexible   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: AM-1-2-10-24-D6-D2   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.20 1.1.81 Actuator module 24 V DC (without ACB) - AM-B-1-2-10-24-D4-D2 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The CPS-M actuator module is used to connect motorised 24 V DC drives to the control panel system. Each actuator module has two motor connections on it, each of which generates an output current of 10 A. Thanks to the monitoring system being used, the drives can be monitored for a wire break, short circuit and overload. The actuator module also features 2 digital outputs and 4 digital inputs that can be configured in the SCS tool. In this tool, users can connect buttons, switches or indicator lights to perform functions such as activating drives or displaying system statuses. There are LEDs on the front of the actuator module that can quickly detect the current system status on site. These LEDs indicate the system and alarm state of the system and the module. Suitable module sockets enable standardised installation on a 35 mm top hat rail and the supply and bus connection via integrated plug connectors. This ensures that it is easy to expand the controller. The use of spring-type terminals on the actuator module also makes installation fast for the service technician.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Monitored motor outputs Number: 2 Output voltage: 24 V DC Output current per connection: max. 10 A Ausgangsstrom gesamt: max. 20 A Cross section: max. 2.5 mm² flexible Usable drives: Polarity-changing drives, ACB-compatible drives Fuse protection: electronic   Digital inputs Number: 4 Switching type: minus or plus active Voltage range: ±30 V DC Assignment: configurable Cross section: max. 1.5 mm² flexible   Digital outputs Number: 2 Output current: max. 50 mA Output voltage: 24 V DC short-circuit resistant Assignment: Configurable Cross section: max. 1.5 mm² flexible   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: AM-1-2-10-24-D6-D2   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.702.69 1.1.82 Actuator module 230 V AC - AM-1-1-08-230-D4-D2 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The modules, including the new 230 V actuator module, are conveniently mounted on standard 35 mm supporting rails using module sockets. Integrated plug connectors are used in the module sockets to ensure the bus communication without wiring. The 230 V actuator module with its EM 230 terminal module expands the existing range of CPS-M control panel functions using the activation / control of motorised 230 V AC drives and their cable monitoring. Each 230 V actuator module has an available motor connection with an allocation of up to 8 A drive current. Thanks to the digital inputs and outputs that are user-configurable through via AdComNet (Advanced Communication Network), operation elements such as ventilation buttons, signal emitters and signal lamps can be set up as desired via the D+H SCS software and interconnected via logic operations. The designated inputs and outputs on the 230 V actuator module, specifically for connecting to the NSV 401 emergency power supply unit, enable a convenient integration of the NSV 401 into the CPS-M System and also enable alarm readiness for 230 V AC drives for 72 hours during a mains outage. The current statuses of the inputs and outputs can be controlled by the CPS-M touch panel at any time. Additionally, the module status is also displayed by both the touch panel and the indicator LEDs on the module itself.   Technical data: Housing dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   230 V AC supply connection Number: 1 Input voltage: 230 V AC / ±15 % Cross section: max. 2.5 mm² flexible   Monitored motor outputs Number: 1 Output voltage: 230 V AC Output current per connection: max. 8 A Output current total: max. 8 A Cross section: max. 2.5 mm² flexible Usable drives: Phase switching drives Fuse protection: Melting fuse   Digital inputs Number: 4 Switching type: minus or plus active Voltage range: 0 - 28 V DC Assignment: configurable (2), NSV fault (1), SGI (1) Cross section: max. 1.5 mm² flexible   Digital outputs Number: 2 Output current: max. 50 mA Output voltage: 24 V DC Short-circuit resistance: Lasting / self-resetting Assignment: Configurable (1), NSV ON/OFF (1) Cross section: max. 1.5 mm² flexibel   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: AM-1-1-08-230-D4-D2   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.85 1.1.83 Trigger module - TMA-1-D4-D12 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised 24 V DC drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The trigger module acts as a connection from the trigger peripheral devices to the control panel system. These can be connected to the four monitored trigger inputs without additional hardware. The user configurable digital inputs and outputs via AdComNet (Advanced Communication Network) make it possible to connect two separate smoke detector and SHEV control panel lines to the trigger module. Use of the connection is not limited to smoke detectors. It can also be reconfigured for use with fire alarm control units using AdComNet (Advanced Communication Network) in the SCS tool. Up to 30 smoke detectors or 10 SHEV control panels can be connected to each of the four trigger inputs. The SCS tool also allows users to assign other functions to digital inputs and outputs not currently in use. There are LEDs on the front of the trigger module that can quickly detect the current system status on site. These LEDs indicate the system and alarm state of the system and the module. The module sockets enable standardised installation on a 35 mm top hat rail and the supply and bus connection via integrated plug connectors. This ensures that it is easy to expand the controller. The use of spring-type terminals on the trigger module also makes installation fast for the service technician.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Monitored line inputs Number: 4 Connection smoke detector: max. 30 Connection SHEV operation panel: max. 10 Connection Fire alarm system / central fire alarm: YES Cross section: max. 1.5 mm² flexiblel   Digital inputs Number: 4 Switching type: minus or plus active Voltage range: ±30 V DC Assignment: configurable Cross section: max. 1.5 mm² flexible   Digital outputs Number: 12 Output current: max. 50 mA Output voltage: 24 V DC short-circuit resistant Assignment: Configurable Cross section: max. 1.5 mm² flexible   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: TMA-1-D4-D12   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.30 1.1.84 Bistable relay module - BRM-1-COC-0006 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised 24 V DC drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The modules, including the new BRM module, are conveniently mounted on standard 35 mm mounting rails using module carriers. Integrated plug connectors are used in the module sockets to ensure the power supply and bus communication without wiring. The BRM module expands the existing range of CPS-M control panel functions with additional configurable and isolated change over contacts, which are activated via the control panel and external voltages and are therefore capable of being used to report statuses and trigger external systems. Thanks to the change over contacts that are user-configurable via AdComNet (Advanced Communication Network), systems and consumers can be given custom set-ups via the D+H SCS software and networked with other assemblies using logic operations. Furthermore, the BRM module change over contacts can be loaded with either 24 V DC or 230 V AC at up to 3 A. Using the bistable contact type of the BRM module change over contacts, it is possible for the change over contacts to take on a predefined state (configurable) even when the system is in a completely de-energized state. This "failsafe" function makes the CPS-M systems safer, especially with respect to triggering external systems. The current states of the change over contacts can be controlled using the CPS-M touch panel at any time. Additionally, the module status is also displayed by both the touch panel and the indicator LEDs on the module itself.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Isolated contacts Number: 6 Design: Changeover contact Design: Bistabile Assignment: Configurable Cross section: max. 2.5 mm² flexible Switching voltage: 12 - 30 V DC / 85 - 265 V AC Switching current: max. 3 A   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: BRM-1-COC-0006   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.15 1.1.85 Input output module - IOM-D1-1212 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised 24 V DC drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The modules, including the new IOM module, are conveniently mounted on standard 35 mm supporting rails using module sockets. Integrated plug connectors are used in the module sockets to ensure the power supply and bus communication without wiring. The IOM module expands the existing functional range of the CPS-M control panel through additional digital inputs and outputs that can be used to evaluate signal states and report system states. Thanks to the digital inputs and outputs that are user-configurable via AdComNet (Advanced Communication Network), operating elements such as ventilation buttons and signal emitters such as signal lamps can be set up as desired via the D+H SCS software and interconnected via logic operations. The current statuses of the inputs and outputs can be controlled by the CPS-M touch panel at any time. Additionally, the module status is also displayed by both the touch panel and the indicator LEDs on the module itself.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Digital inputs Number: 12 Switching type: minus or plus active Voltage range: ±30 V DC Assignment: Configurable Cross section: max. 1.5 mm² flexible   Digital outputs Number: 12 Output current: max. 50 mA Output voltage: 24 V DC short-circuit resistant Assignment: Configurable Cross section: max. 1.5 mm² flexible   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: IOM-D1-1212   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.05 1.1.86 Input output module - ADM-AD1-1212-4 for modular SHEV control panel CPS-M   Performance features: The CPS-M modular SHEV control panel was developed for natural smoke extraction and certified according to EN 12101-10 and ISO 21927-9. Its main function is to trigger motorised 24 V DC drives mounted on-site in order to extract smoke in case of fire or to provide natural ventilation. The modules, including the new ADM module, are conveniently mounted on standard 35 mm supporting rails using module sockets. Integrated plug connectors are used in the module sockets to ensure the power supply and bus communication without wiring. The IOM module expands the existing functional range of the CPS-M control panel through additional analog inputs that can be used to evaluate signal states and report system states. Thanks to the digital inputs and outputs plus analog inputs that are user-configurable via AdComNet (Advanced Communication Network), operating elements such as temperature sensors, CO2 sensors, ventilation buttons and signal emitters such as signal lamps can be set up as desired via the D+H SCS software and interconnected via logic operations. The current statuses of the inputs and outputs can be controlled by the CPS-M touch panel at any time. Additionally, the module status is also displayed by both the touch panel and the indicator LEDs on the module itself.   Technical data: Dimensions (WxHxD): 26 x 130 x 125 mm Installation type: Via module socket on 35 mm top hat rail   Analog & digital inputs Number: 12, 4 of them can be used as analog inputs Switching type: minus or plus active Voltage range: ±30 V DC Assignment: Configurable Cross section: max. 1.5 mm² flexible   Digital outputs Number: 12 Output current: max. 50 mA Output voltage: 24 V DC short-circuit resistant Assignment: Configurable Cross section: max. 1.5 mm² flexible   Fault display: LED - yellow Alarm display: LED - red   Brand: D+H Mechatronic AG Type: ADM-AD1-1212-4   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.65 1.1.87 Module socket 4 times - MS-Q1-RR-TS for modular SHEV control panel CPS-M   Performance features: Module socket for: - 1 controller module - 1 supply module - 2 expansion modules   Can be expanded with connectors integrated into the module base.   Brand: D+H Mechatronic AG Type: MS-Q1-RR-TS   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.61 1.1.88 Extension module socket - MS-S1-DD-TS for modular SHEV control panel CPS-M   Performance features: For holding on expansion module. Can be expanded with connectors integrated into the module base.   Brand: D+H Mechatronic AG Type: MS-S1-DD-TS   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.703.60 Information on the 230 V AC SHEV system For dimensioning a 230 V AC emergency power supply system, please contact your local project consultant.     Planning Support (https://www.dh-partner.com/int/en/service/planning-support) 1.1.89 230 V AC SEHV system 230 V AC / special production according to customer requirements   Performance features: CPS-M1 in conjunction with 230 V AC emergency power supply NSV; Tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017; One-of-a-kind system with a consistent 230 V AC energy supply between controller and drives; More performance - less wiring expense; Ideal for long cable paths; Particularly for heavy duty applications in roof areas;   Technical data - NSV 401: Supply: 230 V AC / +10 % till -15 % / 50 Hz High/low-voltage regulation: -13 % / +13 % Max. output: 3200 VA / 2000 W (14.6 A) Mains operation: 197 - 250 V AC Support operation: 230 V AC (sine ±5 %) Ability to be overloaded: 10 - 25 s / > 130 % 1.5 s AC efficiency: > 95 % Nominal battery voltage: 48 V DC (nominal) Recommended temperature range: +15 °C till +25 °C Cooling: Fan cooling Noise level: < 45 dB   Brand: D+H Mechatronic AG   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk 1.1.90 TP-R2-S - HMI Touch panel - freely configurable 24 V DC / Special production according to customer requirements   Performance features: Modern and versatile HMI touch panel with optional 7‘‘, 10" or 15" screen diagonal and a resolution of up to 1024 x 768 pixels and Modbus RTU/TCP interface. This touch panel series can be connected to the CPS-M over the ACN-GW501-MRTU-0200 ACN/Modbus Gateway. Various visualisation and control systems can be implemented via this touch panel. The touch panel offers a versatile range of functions, which can be customised by D+H depending on the object. This includes the programming of the functions and the visualisation of the surface.   Functions (extract): Versatile graphic elements for display and operation Animated interface Individual graphic elements and images possible Extensive data logging User administration and security Alarm and events Own language switching for users programmable via text tables XY-graph with up to 64 characteristic curves possible Scheduler for calendar controlled functions Use as fire brigade control panel   Technical data 7" touch display: Supply: 24 V DC / 0.15 A Resolution: 800 x 480 pixel Display area: 154.08 x 85.92 mm Contrast: 500:1 Brightness: 250 cd/m² Touch panel: 4-wire resistive Temperature range: 0 °C till +50 °C Humidity: 10 - 90 % RH (non-condensing) Dimensions (WxHxD): 204 x 150 x 34 mm Weight: 0.5 kg   Technical data 10" touch display: Supply: 24 V DC / 0.25 A Resolution: 1024 x 600 pixel Display area: 222.72 x 125.28 mm Contrast: 500:1 Brightness: 400 cd/m² Touch panel: 4-wire resistive Temperature range: 0 °C till +50 °C Humidity: 10 - 90 % RH (non-condensing) Dimensions (WxHxD): 280 x 193 x 36 mm Weight: 0.9 kg   Technical data 15" touch display: Supply: 24 V DC / 0.67 A Resolution: 1024 x 768 pixel Display area: 304.13 x 228.10 mm Contrast: 800:1 Brightness: 420 cd/m² Touch panel: 4-wire resistive Temperature range: 0 °C till +50 °C Humidity: 10 - 90 % RH (non-condensing) Dimensions (WxHxD): 398 x 298 x 47 mm Weight: 3 kg   Scope of supply: Touch panel optionally mounted in lockable surface-mounted housing, individually for installation in the wall or installed in the CPS-M control cabinet   Brand: D+H Mechatronic AG Type: TP-R2-S   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 31.700.05 1.1.91 SHEV control panel - basic- CPS-B1-2.5-0101 24 V DC / 2.5 A / 1 line / 1 drive group   Performance features: A stabilised output voltage is provided by the control panel. A maximum of 8 SHEV operation panels and 8 fire detectors can be connected per line. The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Only detectors approved by D+H may be used for the connection of fire detectors. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit. Connection options for optical and acoustic alarm devices are also available. The control panel can be used for daily ventilation, ventilation time can be set on the central unit. An optional wind / rain sensor can be connected directly.   Technical data: Supply: 195 - 253 V AC / 50 Hz / 140 VA Stand-by power: < 2 W Output: 24 V DC / 2.5 A Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Plastic Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 104 mm   Scope of supply: Control board, with plastic housing with spare key , without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-B1-2.5-0101   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.119.10 1.1.92 SHEV control panel - basic- CPS-B1-5-0101 24 V DC / 5 A / 1 line / 1 drive group   Performance features: A stabilised output voltage is provided by the control panel. A maximum of 8 SHEV operation panels and 8 fire detectors can be connected per line. The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344, DIN EN 12101-10 and EN 62368-1:2014 + A11:2017 and also fulfils the building authority requirements in accordance with DIN 18232-9. Only detectors approved by D+H may be used for the connection of fire detectors. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit. Connection options for optical and acoustic alarm devices are also available. The control panel can be used for daily ventilation, ventilation time can be set on the central unit. An optional wind / rain sensor can be connected directly.   Technical data: Supply: 195 - 253 V AC / 50 Hz / 145 VA Stand-by power: < 2 W Output: 24 V DC / 5 A Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Plastic Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 104 mm   Scope of supply: Control board, with plastic housing with spare key , without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-B1-5-0101   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.119.15 1.1.93 SHEV control panel - compact - CPS-P1-020-0202 24 V DC / 20 A / 2 Lines / 2 drive groups   Performance features: Compact, networkable SHEV control panel with emergency power supply and stabilised output voltage for controlling 24 V DC drive systems. The SHEV control panel has been tested and certified in accordance with ISO ISO 21927-9, VdS 2581, VdS 2593, VdS 2594, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Each drive group can supply up to 20 A and cable cross-sections greater than 16 mm² can be realised using optional DIN rail modules. Up to 8 SHEV operating panels and up to 14 fire detectors can be connected per line (only detectors approved by D+H may be used); Signals can be output via two potential-free relays; Up to 16 control panels can be used in the network via the main/sub network; lines are triggered and reset together in the network; it is possible to remove lines of individual SHEV control units from the network to form an independent smoke extraction section; firmware updates can be carried out in the network; Battery status-monitored battery emergency power supply for at least 72 h; Temperature-controlled battery charging; SHEV and ventilation functions can be parameterised via dip switches without software; Switchable SHEV functions: Fault = Alarm; Two-smoke detector dependency; SHEV retriggering function and remote smoke detector reset; Group fault equals alarm, Cable monitoring for short circuit and interruption; Slot for additional module; Combination of a SHEV / house alarm function possible; comfort ventilation functions; Connection option for optical and acoustic alarm devices; Can be used for daily ventilation; Ventilation time and opening width adjustable; Wind / rain sensor can be connected without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 550 VA Stand-by power: < 5 W Output: 24 V DC / 20 A Ripple: < 0.5 Vpp Mode of operation: - Monitoring: Continuous duty - Alarm / Ventilation: Short-time duty (30 % duty cycle) - Network (Main/Sub) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Rigid ABS Colour: Light grey (~ RAL 7035) Dimension (WxHxD): 400 x 500 x 240 mm   Scope of supply: Central circuit board, with lockable plastic housing incl. key, with wired switching power supply units and terminal blocks for mains connection, without batteries (batteries must be ordered separately)   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.120.10 1.1.94 SHEV control panel - compact - CPS-P1-020-0202-B 24 V DC / 20 A / 2 Lines / 2 drive groups   Performance features: Compact, networkable SHEV control panel with emergency power supply and stabilised output voltage for controlling 24 V DC drive systems. The SHEV control panel has been tested and certified in accordance with ISO ISO 21927-9, VdS 2581, VdS 2593, VdS 2594, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Each drive group can supply up to 20 A and cable cross-sections greater than 16 mm² can be realised using optional DIN rail modules. Up to 8 SHEV operating panels and up to 14 fire detectors can be connected per line (only detectors approved by D+H may be used); Signals can be output via two potential-free relays; Battery status-monitored battery emergency power supply for at least 72 h; Temperature-controlled battery charging; SHEV and ventilation functions can be parameterised via dip switches without software; Switchable SHEV functions: Fault = Alarm; Two-smoke detector dependency; SHEV retriggering function and remote smoke detector reset; Group fault equals alarm, Cable monitoring for short circuit and interruption; Combination of a SHEV / house alarm function possible; comfort ventilation functions; Connection option for optical and acoustic alarm devices; Can be used for daily ventilation; Ventilation time and opening width adjustable; Wind / rain sensor can be connected without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 550 VA Stand-by power: < 5 W Output: 24 V DC / 20 A Ripple: < 0.5 Vpp Mode of operation: - Monitoring: Continuous duty - Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Rigid ABS Colour: Light grey (~ RAL 7035) Dimension (WxHxD): 400 x 500 x 240 mm   Scope of supply: Central circuit board, with lockable plastic housing incl. key, with wired switching power supply units and terminal blocks for mains connection, without batteries (batteries must be ordered separately)   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.120.15 1.1.95 SHEV control panel - compact - CPS-P1-040-0202 24 V DC / 40 A / 2 Lines / 2 drive groups   Performance features: Compact, networkable SHEV control panel with emergency power supply and stabilised output voltage for controlling 24 V DC drive systems. The SHEV control panel has been tested and certified in accordance with ISO ISO 21927-9, VdS 2581, VdS 2593, VdS 2594, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Each drive group can supply up to 20 A and cable cross-sections greater than 16 mm² can be realised using optional DIN rail modules. Up to 8 SHEV operating panels and up to 14 fire detectors can be connected per line (only detectors approved by D+H may be used); Signals can be output via two potential-free relays; Up to 16 control panels can be used in the network via the main/sub network; lines are triggered and reset together in the network; it is possible to remove lines of individual SHEV control units from the network to form an independent smoke extraction section; firmware updates can be carried out in the network; Battery status-monitored battery emergency power supply for at least 72 h; Temperature-controlled battery charging; SHEV and ventilation functions can be parameterised via dip switches without software; Switchable SHEV functions: Fault = Alarm; Two-smoke detector dependency; SHEV retriggering function and remote smoke detector reset; Group fault equals alarm, Cable monitoring for short circuit and interruption; Slot for additional module; Combination of a SHEV / house alarm function possible; comfort ventilation functions; Connection option for optical and acoustic alarm devices; Can be used for daily ventilation; Ventilation time and opening width adjustable; Wind / rain sensor can be connected without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 1010 VA Stand-by power: < 6 W Output: 24 V DC / 40 A Ripple: < 0.5 Vpp Mode of operation: - Monitoring: Continuous duty - Alarm / Ventilation: Short-time duty (30 % duty cycle) - Network (Main/Sub) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Rigid ABS Colour: Light grey (~ RAL 7035) Dimension (WxHxD): 400 x 500 x 240 mm   Scope of supply: Central circuit board, with lockable plastic housing incl. key, with wired switching power supply units and terminal blocks for mains connection, without batteries (batteries must be ordered separately)   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.120.11 1.1.96 SHEV control panel - compact- CPS-P1-040-0202-B 24 V DC / 40 A / 2 Lines / 2 drive groups   Performance features: Compact, networkable SHEV control panel with emergency power supply and stabilised output voltage for controlling 24 V DC drive systems. The SHEV control panel has been tested and certified in accordance with ISO ISO 21927-9, VdS 2581, VdS 2593, VdS 2594, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Each drive group can supply up to 20 A and cable cross-sections greater than 16 mm² can be realised using optional DIN rail modules. Up to 8 SHEV operating panels and up to 14 fire detectors can be connected per line (only detectors approved by D+H may be used); Signals can be output via two potential-free relays; Battery status-monitored battery emergency power supply for at least 72 h; Temperature-controlled battery charging; SHEV and ventilation functions can be parameterised via dip switches without software; Switchable SHEV functions: Fault = Alarm; Two-smoke detector dependency; SHEV retriggering function and remote smoke detector reset; Group fault equals alarm, Cable monitoring for short circuit and interruption; Combination of a SHEV / house alarm function possible; comfort ventilation functions; Connection option for optical and acoustic alarm devices; Can be used for daily ventilation; Ventilation time and opening width adjustable; Wind / rain sensor can be connected without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 1010 VA Stand-by power: < 6 W Output: 24 V DC / 40 A Ripple: < 0.5 Vpp Mode of operation: - Monitoring: Continuous duty - Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Rigid ABS Colour: Light grey (~ RAL 7035) Dimension (WxHxD): 400 x 500 x 240 mm   Scope of supply: Central circuit board, with lockable plastic housing incl. key, with wired switching power supply units and terminal blocks for mains connection, without batteries (batteries must be ordered separately)   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.120.16 1.1.97 SHEV control panel - RZN 4503-T, orange 24 V DC / 3 A / 1 line / 1 drive group   Performance features: Central unit with integrated SHEV main operation panel and ventilation button in a solid fire-proof aluminium housing. The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9. A stabilised output voltage is provided by the control panel. A maximum of 8 SHEV operation panels and 14 fire detectors can be connected per line. Only detectors approved by D+H may be used for the connection of fire detectors. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit The control unit has a slot for an additional module. Connection options for optical and acoustic alarm devices are also available. The additional module can be used for daily ventilation, ventilation time and opening width can be set on the central unit. Battery charging is temperature-controlled - charge and status checks are displayed. An optional wind / rain sensor can be connected without an additional module. The control unit has 2 freely programmable and isolated signalling contacts.   Technical data: Supply: 230 V AC / 50 Hz / 100 VA Stand-by power: < 5 W Output: 24 V DC / 3 A Ripple: < 0.5 mVss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Aluminium Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 156 x 235 x 82 mm   Scope of supply: Control board in lockable surface-type housing with lockable door, spare key, designations labels in 32 languages, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: RZN 4503-T   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.107.30 1.1.98 SHEV control panel - RZN 4503-T/G, grey 24 V DC / 3 A / 1 line / 1 drive group   Performance features: Central unit with integrated SHEV main operation panel and ventilation button in a solid fire-proof aluminium housing. The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9. A stabilised output voltage is provided by the control panel. A maximum of 8 SHEV operation panels and 14 fire detectors can be connected per line. Only detectors approved by D+H may be used for the connection of fire detectors. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit The control unit has a slot for an additional module. Connection options for optical and acoustic alarm devices are also available. The additional module can be used for daily ventilation, ventilation time and opening width can be set on the central unit. Battery charging is temperature-controlled - charge and status checks are displayed. An optional wind / rain sensor can be connected without an additional module. The control unit has 2 freely programmable and isolated signalling contacts.   Technical data: Supply: 230 V AC / 50 Hz / 100 VA Stand-by power: < 5 W Output: 24 V DC / 3 A Ripple: < 0.5 mVss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Aluminium Colour: Grey (~ RAL 7035) Dimensions (WxHxD): 156 x 235 x 82 mm   Scope of supply: Control board in lockable surface-type housing with lockable door, spare key, designations labels in 32 languages, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: RZN 4503-T/G   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.107.40 1.1.99 SHEV control panel - RZN 4503-T/Y, yellow 24 V DC / 3 A / 1 line / 1 motor groups   Performance features: Central unit with integrated SHEV main operation panel and ventilation button in a solid fire-proof aluminium housing. The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9. A stabilised output voltage is provided by the control panel. A maximum of 8 SHEV operation panels and 14 fire detectors can be connected per line. Only detectors approved by D+H may be used for the connection of fire detectors. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit The control unit has a slot for an additional module. Connection options for optical and acoustic alarm devices are also available. The additional module can be used for daily ventilation, ventilation time and opening width can be set on the central unit. Battery charging is temperature-controlled - charge and status checks are displayed. An optional wind / rain sensor can be connected without an additional module. The control unit has 2 freely programmable and isolated signalling contacts.   Technical data: Supply: 230 V AC / 50 Hz / 100 VA Stand-by power: < 5 W Output: 24 V DC / 3 A Ripple: < 0.5 mVss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Aluminium Colour: Yellow (~ RAL 1004) Dimensions (WxHxD): 156 x 235 x 82 mm   Scope of supply: Control board in lockable surface-type housing with lockable door, spare key, designations labels in 32 languages, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: RZN 4503-T/Y   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.107.60 1.1.100 SHEV control panel set - RZN 4503-T Set, orange 24 V DC / 3 A / 1 line / 1 drive group   Performance features: Central unit with integrated SHEV main operation panel and ventilation button in a solid fire-proof aluminium housing. The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9. A stabilised output voltage is provided by the control panel. A maximum of 8 SHEV operation panels and 14 fire detectors can be connected per line. Only detectors approved by D+H may be used for the connection of fire detectors. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit The control unit has a slot for an additional module. Connection options for optical and acoustic alarm devices are also available. The additional module can be used for daily ventilation, ventilation time and opening width can be set on the central unit. Battery charging is temperature-controlled - charge and status checks are displayed. An optional wind / rain sensor can be connected without an additional module. The control unit has 2 freely programmable and isolated signalling contacts.   Set consisting of: SHEV control panel; External RT 45 button or manually triggering a SHEV system in case of fire; Fire detector SD-O 371; Batterie for providing 72 hours of emergency power;   Technical data - Control panel RZN 4503-T: Supply: 230 V AC / 50 Hz / 100 VA Stand-by power: < 5 W Output: 24 V DC / 3 A Ripple: < 0.5 mVss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Aluminium Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 156 x 235 x 82 mm   Technical data - RT 45: Supply: 24 V DC (18 - 28 V DC) Type of protection: IP 40 Temperature range: -5 C° till +40 °C Housing: Die-cast aluminium (surface-type housing) Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 129 x 138 x 39 mm   Technical data - SD-O 371: Nominal voltage: 24 V DC Monitoring area: max. 110 m² Monitoring hight: max. 12 m Alarm indicator: LED rot Temperature range: -20 °till +72 °C Air humidity: ≤ 95 % Type of protection: IP 40 Connection terminals: 0.6 mm Ø till 2 mm² Housing: ABS Colour: White (~ RAL 9010) Specification: EN 54-7 VdS approval: G 213066   Technical data - Akku Typ 8: Voltage: 12 V DC Battery capacity: 3.4 Ah ±15 % Dimensions (WxHxD): ca. 134 x 66 x 67 mm   Scope of supply: Control board in lockable surface-type housing with lockable door, spare key, designations labels in 32 languages, RT 45, SD-O 371 and integrated emergency power supply (1x Akku Typ 8)   Brand: D+H Mechatronic AG Type: RZN 4503-T Set   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.107.97 1.1.101 Cable duct adapter - KK 4503 for RZN 4503-T   Performance features: To create a comfortable insertion situation;   Technical data: Material: Steel sheet Surface: Powder coated Colour: Grey (~ RAL 7035)   Scope of supply: Cable duct adapter, instruction for use   Brand: D+H Mechatronic AG Type: KK 4503   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.107.90 1.1.102 SHEV control panel - compact - RZN 4408-K 24 V DC / 8 A / 1 line / 2 drive groups   Performance features: SHEV controller - AdComNet ready; The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Stabilised output voltage; Connection of up to 8 SHEV operation panels and 14 fire detectors per line (Only detectors permitted by D+H may be used); Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; Switchable SHEV functions: Fault equal to alarm; SHEV retriggering function and smoke detector remote reset; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: 4.5 W Output: 24 V DC (21.6 - 28.5 V DC) / 8 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 - in plastic housing (GEH-KST 63.600.81) IP 54 - in steel sheet housing (GEH-S-RWA 30.105.30) Temperature range: -5 °C till +40 °C Line / Group: 1 / 2 Housing: Plastic with steel sheet door Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 100 mm Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 400 x 300 x 120 mm   Scope of supply: Control board, without housing (housing with spare key must be ordered separately), without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: RZN 4408-K   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.117.30 1.1.103 SHEV control panel - compact - RZN 4404-M 24 V DC / 4 A / 2 lines / 2 drive groups   Performance features SHEV controller - AdComNet ready; The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Stabilised output voltage; Connection of up to 8 SHEV operation panels and 14 fire detectors per line (Only detectors permitted by D+H may be used); Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; Switchable SHEV functions: Fault equal to alarm; SHEV retriggering function and smoke detector remote reset; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: 6.8 W Output: 24 V DC (21.6 - 28.5 V DC) / 4 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 - in plastic housing (GEH-KST 63.600.81) IP 54 - in steel sheet housing (GEH-S-RWA 30.105.30) Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Plastic with steel sheet door Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 100 mm Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 400 x 300 x 120 mm   Scope of supply: Control board, without housing (housing with spare key must be ordered separately), without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: RZN 4404-M   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.117.10 1.1.104 SHEV control panel - compact - RZN 4408-M 24 V DC / 8 A / 2 lines / 3 drive groups   Performance features: SHEV controller - AdComNet ready; The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Stabilised output voltage; Connection of up to 8 SHEV operation panels and 14 fire detectors per line (Only detectors permitted by D+H may be used); Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; Switchable SHEV functions: Fault equal to alarm; SHEV retriggering function and smoke detector remote reset; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 240 VA Stand-by power: 5 W Output: 24 V DC (21.6 - 28.5 V DC) / 8 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 - in plastic housing (GEH-KST 63.600.81) IP 54 - in steel sheet housing (GEH-S-RWA 30.105.30) Temperature range: -5 °C till +40 °C Line / Group: 2 / 3 Housing: Plastic with steel sheet door Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 100 mm Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 400 x 300 x 120 mm   Scope of supply: Control board, without housing (housing with spare key must be ordered separately), without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: RZN 4408-M   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.117.20 1.1.105 SHEV control panel - compact - RZN 4416-M 24 V DC / 16 A / 2 lines / 3 drive groups   Performance features: SHEV controller - AdComNet ready; The SHEV control panel is tested and certified according to ISO 21927-9, VdS 2581, VdS 2593, VdS 2344 and DIN EN 12101-10 and also fulfils the building authority requirements in accordance with DIN 18232-9; Stabilised output voltage; Connection of up to 8 SHEV operation panels and 14 fire detectors per line (Only detectors permitted by D+H may be used); Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; Switchable SHEV functions: Fault equal to alarm; SHEV retriggering function and smoke detector remote reset; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 500 VA Stand-by power: 13.6 W Output: 24 V DC (21.6 - 28.5 V DC) / 16 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 30 Temperature range: -5 °C till +40 °C Line / Group: 2 / 3 Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions ((WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel in lockable steel sheet housing, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: RZN 4416-M   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.109.02 1.1.106 SHEV control panel - compact - DAC 4408-K 24 V DC / 8 A / 1 line / 1 drive group   Performance features: SHEV control - AdComNet ready; Approval according to EN 12101-10 and certified according to NF 537, developed according to ISO 21927-9; Stabilised output voltage; Connection of up to 2 SHEV operation panels per control panel; Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; SHEV retriggering function; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; LED status display visible from outside; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: 5 W / 6.7 VA Output: 24 V DC (21.6 - 28.5 V DC) / 8 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Plastic with steel sheet door Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 100 mm   Scope of supply: Control panel with plastic housing with steel sheet door incl. keys, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: DAC 4408-K   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.118.70 1.1.107 SHEV control panel - compact - DAC 4408-KS 24 V DC / 8 A / 1 line / 1 drive group   Performance features: SHEV control - AdComNet ready; Approval according to EN 12101-10 and certified according to NF 537, developed according to ISO 21927-9; Stabilised output voltage; Connection of up to 2 SHEV operation panels per control panel; Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; SHEV retriggering function; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; LED status display visible from outside; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: 5 W / 6.7 VA Output: 24 V DC (21.6 - 28.5 V DC) / 8 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 400 x 300 x 120 mm   Scope of supply: Control panel with steel sheet housing incl. keys, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: DAC 4408-KS   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.118.75 1.1.108 SHEV control panel - compact - DAC 4404-M 24 V DC / 4 A / 2 lines / 2 drive groups   Performance features SHEV control - AdComNet ready; Approval according to EN 12101-10 and certified according to NF 537, developed according to ISO 21927-9; Stabilised output voltage; Connection of up to 4 SHEV operation panels per control panel; Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; SHEV retriggering function; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; LED status display visible from outside; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: 6.8 W / 22 VA Output: 24 V DC (21.6 - 28.5 V DC) / 4 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Plastic with steel sheet door Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 100 mm   Scope of supply: Control panel with plastic housing with steel sheet door incl. keys, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: DAC 4404-M   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.118.50 1.1.109 SHEV control panel - compact - DAC 4404-MS 24 V DC / 4 A / 2 lines / 2 drive groups   Performance features SHEV controller - AdComNet ready; SHEV control - AdComNet ready; Approval according to EN 12101-10 and certified according to NF 537, developed according to ISO 21927-9; Stabilised output voltage; Connection of up to 4 SHEV operation panels per control panel; Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; SHEV retriggering function; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; LED status display visible from outside; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: 6.8 W / 22 VA Output: 24 V DC (21.6 - 28.5 V DC) / 4 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 400 x 300 x 120 mm   Scope of supply: Control panel with steel sheet housing incl. keys, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: DAC 4404-MS   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.118.55 1.1.110 SHEV control panel - compact - DAC 4408-M 24 V DC / 8 A / 2 lines / 2 drive groups   Performance features: SHEV control - AdComNet ready; Approval according to EN 12101-10 and certified according to NF 537, developed according to ISO 21927-9; Stabilised output voltage; Connection of up to 4 SHEV operation panels per control panel; Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; SHEV retriggering function; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; LED status display visible from outside; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 240 VA Stand-by power: 4.5 W / 7 VA Output: 24 V DC (21.6 - 28.5 V DC) / 8 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Plastic with steel sheet door Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 100 mm   Scope of supply: Control panel with plastic housing with steel sheet door incl. keys, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: DAC 4408-M   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.118.60 1.1.111 SHEV control panel - compact - DAC 4408-MS 24 V DC / 8 A / 2 lines / 2 drive groups   Performance features: SHEV control - AdComNet ready; Approval according to EN 12101-10 and certified according to NF 537, developed according to ISO 21927-9; Stabilised output voltage; Connection of up to 4 SHEV operation panels per control panel; Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; SHEV retriggering function; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; LED status display visible from outside; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 240 VA Stand-by power: 4.5 W / 7 VA Output: 24 V DC (21.6 - 28.5 V DC) / 8 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 2 / 2 Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions (WxHxD): 400 x 300 x 120 mm   Scope of supply: Control panel with steel sheet housing incl. keys, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: DAC 4408-MS   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.118.65 1.1.112 SHEV control panel - compact - DAC 4416-M 24 V DC / 16 A / 2 lines / 3 drive groups   Performance features: SHEV control - AdComNet ready; Approval according to EN 12101-10 and certified according to NF 537, developed according to ISO 21927-9; Stabilised output voltage; Connection of up to 4 SHEV operation panels per control panel; Min. 72 hr battery backup supply; Temperature-controlled battery charge; Batterie charge and status check; SHEV retriggering function; Codable SHEV and ventilation functions; Combination of a SHEV- / building alarm function possible; Comfort ventilation functions; Line monitoring for short circuit and interruption; Slot for additional module; Possible connection for optical and acoustical alarm devices; LED status display visible from outside; Usable for daily ventilation; Ventilation time and opening width adjustable; Wind/rain sensor connectable without additional module;   Technical data: Supply: 230 V AC / 50 Hz / 500 VA Stand-by power: 14 W / 55 VA Output: 24 V DC (21.6 - 28.5 V DC) / 16 A Ripple: < 2 Vss Mode of operation -Monitoring: Continuous duty -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 2 / 3 Housing: Steel sheet Colour: Light grey (~ RAL 7035) Dimensions ((WxHxD): 500 x 500 x 210 mm   Scope of supply: Control panel with steel sheet housing incl. keys, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: DAC 4416-M   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.118.80 1.1.113 SHEV control panel - basic - CPS-B1-2.5-0101-FR 24 V DC / 2.5 A / 1 line / 1 drive group   Performance features: A stabilised output voltage is provided by the control panel. 2 SHEV operation panels can be connected per line. The control unit is developed according EN 12101-10 as well as certified according to NF 537. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit. Connection options for optical and acoustic alarm devices are also available. The control panel can be used for daily ventilation, ventilation time can be set on the central unit. An optional wind / rain sensor can be connected directly.   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: <2 W / 10 VA Output: 24 V DC / 2.5 A Mode of operation Monitoring: Continuous duty Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Plastic Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 104 mm   Scope of supply: Control board, with housing (housing with spare key), without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-B1-2.5-0101-FR   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.119.30 1.1.114 SHEV control panel - basic - CPS-B1-5-0101-FR 24 V DC / 5 A / 1 line / 1 drive group   Performance features: A stabilised output voltage is provided by the control panel. A maximum of 2 SHEV operation panels can be connected per line. The control unit is developed according EN 12101-10 as well as certified according to NF 537. An integrated emergency battery power for at least 72 hours is integrated in the housing. Switchable SHEV safety functions: Fault equal to alarm. SHEV retriggering function, smoke detector remote reset, cable monitoring for short circuit and interruption can be realised with the control unit. Connection options for optical and acoustic alarm devices are also available. The control panel can be used for daily ventilation, ventilation time can be set on the central unit. An optional wind / rain sensor can be connected directly.   Technical data: Supply: 230 V AC / 50 Hz / 120 VA Stand-by power: <2 W / 16 VA Output: 24 V DC / 5 A Mode of operation Monitoring: Continuous duty Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Line / Group: 1 / 1 Housing: Plastic Colour: White (~ RAL 9016) Dimensions (WxHxD): 310 x 310 x 104 mm   Scope of supply: Control board, with housing (housing with spare key), without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-B1-5-0101-FR   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.119.35 Information CPS-M1-S SHEV control panel based on AdComNet   The CPS-M is not only the first control panel that has the ability to communicate with other CPS-M control panels and other AdComNet-enabled products, but also the first product that is based directly on AdComNet. All parameterisation, function settings and assignment of lines and groups are set using the "SCS" (Service & Configuration Suite) operating software. 1.1.115 SHEV control panel - modular - CPS-M1-FR-020-0204-WD 24 V DC / 20 A / 2 RM/RT-lines / 4 motor groups, without touch panel   Performance features: The SHEV control panel is tested and certified according to NF S61-938 and tested and developed according to EN 12101-10 and ISO 21927-9;; Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 4 SHEV operation panels can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. In addition, information about the status of the control panel is displayed on the outside of the door. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 2x actuator module with advanced line monitoring - 1x trigger module with one CMSI   Technical data: Supply: 230 V AC / 50 Hz / 530 VA Output: 24 V DC / 20 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Housing: Steel sheet (500 x 500 x 210 mm) Colour: Light grey (~ RAL 7035)   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-FR-020-0204-WD   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 31.701.95 1.1.116 SHEV control panel - modular - CPS-M1-FR-040-0206-WD 24 V DC / 40 A / 2 RM/RT-lines / 6 motor groups, without touch panel   Performance features: The SHEV control panel is tested and certified according to NF S61-938 and tested and developed according to EN 12101-10 and ISO 21927-9;; Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 4 SHEV operation panels can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. In addition, information about the status of the control panel is displayed on the outside of the door. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 1x power supply module - 3x actuator module with advanced line monitoring - 1x trigger module with one CMSI   Technical data: Supply: 230 V AC / 50 Hz / 1040 VA Output: 24 V DC / 40 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Housing: Steel sheet (600 x 800 x 250 mm) Colour: Light grey (~ RAL 7035)   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-FR-040-0206-WD   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 31.701.80 1.1.117 SHEV control panel - modular - CPS-M1-FR-060-0210-WD 24 V DC / 60 A / 2 RM/RT-lines / 10 motor groups, without touch panel   Performance features: The SHEV control panel is tested and certified according to NF S61-938 and tested and developed according to EN 12101-10 and ISO 21927-9;; Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 4 SHEV operation panels can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. In addition, information about the status of the control panel is displayed on the outside of the door. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module with advanced line monitoring - 1x trigger module with one CMSI   Technical data: Supply: 230 V AC / 50 Hz / 1570 VA Output: 24 V DC / 60 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Housing: Steel sheet (600 x 800 x 250 mm) Colour: Light grey (~ RAL 7035)   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-FR-060-0210-WD   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 31.701.90 1.1.118 SHEV control panel - modular - CPS-M1-FR-080-0210-WD 24 V DC / 80 A / 2 RM/RT-lines / 10 motor groups, without touch panel   Performance features: The SHEV control panel is tested and certified according to NF S61-938 and tested and developed according to EN 12101-10 and ISO 21927-9;; Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 4 SHEV operation panels can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. In addition, information about the status of the control panel is displayed on the outside of the door. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 5x actuator module with advanced line monitoring - 1x trigger module with one CMSI   Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Housing: Steel sheet (800 x 1000 x 300 mm) Colour: Light grey (~ RAL 7035)   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-FR-080-0210-WD   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 31.701.70 1.1.119 SHEV control panel - modular - CPS-M1-FR-080-0216-WD 24 V DC / 80 A / 2 RM/RT-lines / 16 motor groups, without touch panel   Performance features: The SHEV control panel is tested and certified according to NF S61-938 and tested and developed according to EN 12101-10 and ISO 21927-9;; Functions and dependencies can be individually parameterised via the D+H software SCS. The motor connections are electronically protected. The integrated supply module uses an external temperature sensor and prolongs the service life of the batteries through temperature-controlled battery charging. Each supply module can also be connected to emergency and non-emergency peripherals of up to 500 mA. Up to 4 SHEV operation panels can be connected per trigger module as standard. Control, alarm and fault can be displayed via 12 digital outputs of the trigger module. In addition, information about the status of the control panel is displayed on the outside of the door. Optionally, ACB drives and pole reversing drives can be connected to one actuator module in two groups of 10 amps each. Each actuator module has 6 freely programmable digital inputs for connecting ventilation buttons or processing OPEN and CLOSE messages. Digital outputs (2) of the actuator module can be freely programmed. Internal wiring of the modules and system extensions is not necessary due to the integrated plug connection. Batteries ensure an emergency power supply of the SHEV control panel for 72 hours.   Installed modules: - 1x controller module - 2x power supply module - 8x actuator module with advanced line monitoring - 1x trigger module with one CMSI     Technical data: Supply: 230 V AC / 50 Hz / 2080 VA Output: 24 V DC / 80 A Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 32D Temperature range: -5 °C till +40 °C Housing: Steel sheet (800 x 1000 x 300 mm) Colour: Light grey (~ RAL 7035)   Scope of supply: Control panel in lockable surface-type housing, touch panel, mains connection terminal, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-FR-080-0216-WD   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 31.701.60 1.1.120 SHEV control panel - modular - CPS-M1-FR-S - freely configurable 24 V DC / Special production according to customer requirements   Performance features: The smoke vent control panel is tested and approved according to NF S61-938; Variable modular technology for complex position requirements; Flexible system design with functional modules; Installation on 35 mm supporting rail system; Expandable with up to 30 CPS-M function modules incl. CM module; Possible function module: - Controller module - CM-BT1-D4-P2 - Supply module - PSM-1-24-40 - Actuator module 24 V DC - AM-1-2-10-24-D6-D2-FR - Actuator module 230 V AC - AM-1-1-08-230-D4-D2 - Trigger module - TMA-1-D4-D12 - Bistable relay module - BRM-1-COC-0006 - Input output module - IOM-D1-1212   Addition of the drive current in 20 A steps; Max. 10 A drive current per 24 V DC group; Connection of up to 2 SHEV operation panels per line; Integrated comfort functions for daily ventilation: - Storage/key operation - OPEN running time limit - Ventilation time limitation   Integrated protection functions: - Weather signal = CLOSED control - Mains outage = CLOSED control   Components can be retrofitted in case of building modifications;   Switchable SHEV safety functions: - Fault equal to alarm - Alarm = CLOSED control   Technical data: Supply: 230 V AC / 50 Hz Output: 24 V DC Ripple: < 50 mVss Mode of operation -Monitoring: Pulse operation -Alarm / Ventilation: Short-time duty (30 % duty cycle) Type of protection: IP 54 Temperature range: -5 °C till +40 °C Housing: Steel sheet Colour: Light grey (~ RAL 7035)   Scope of supply: Control panel in lockable surface-type housing, touch panel, without batteries (batteries must be ordered separately)   Brand: D+H Mechatronic AG Type: CPS-M1-FR-S   The D+H partner on site is at your disposal for design variants.   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 31.700.03 Information AdComNet Convenience and reliability intelligently combined AdComNet (Advanced Communication Network) is the bus technology from D+H, with which you can integrate decentralised standard SHEV control systems into smoke extraction and ventilation concepts which can be programmed easily and flexibly. The modularly designed network technology is the first VdS-certified bus system for SHEV on the market.     A complex smoke vent scenario, controlled easily and reliably With AdComNet the conventional control panels can be linked to enable complex scenarios for opening and closing windows or other ventilation equipment, depending on how the room is being used. Smoke vent example: If a fire breaks out on one storey, the closed windows on that storey open immediately and conduct the hazardous fire smoke out of the building. On the remaining storeys unaffected by the fire, AdComNet closes the open windows to prevent toxic combustion gases from entering. The closed windows in the stairwell are also opened automatically, to keep this escape route free of smoke. By dividing the bus system into independent segments, the individual fire compartments remain functional even if there is a break in communication.     AdComNet: modular and flexible The modular and decentralised bus system has been designed as a long-term economical solution for all types of buildings in which not only SHEV systems, but also natural ventilation systems are used. Since the bus system is easy to reprogram if the room will be used differently, AdComNet is ideal for building types with sophisticated requirements for SHEV and ventilation, such as buildings with multiple storeys and fire compartments (office and administrative buildings, schools, places of assembly, production facilities etc.).   The system can be expanded or adapted at any time, either while it is being installed and set up, or during later conversions or retrofits. Smoke compartments, load and zone groups as well as the corresponding field devices can be reprogrammed without changing any cables. No need for laborious and expensive new installations and cabling.     Overview of advantages: - Large savings potential thanks to lower cabling effort, significant reduction of cable cross-sections and lengths - Only a tenth of the usual power consumption per node item, thanks to low-power technology - Cost savings when designing and dimensioning the SHEV controllers thanks to a reduced need for battery power and size - No special power supply required in the event of a mains outage; initial states are kept - No need for special system integrators     For dimensioning a SHEV AdComNet bussystem, please contact your local project consultant.   https://www.dh-partner.com/en/service/planning-support.html   1.1.121 I/O module - ACN-IO501 for AdComNet   Performance features: I/O Module for supplying and integrating digital signals out of or into the AdComNet network; Integrated router and repeater; In case of defetc in another segment the functionalities within & below the segment stay intact universal interface towards other networks because of floating contacts; Pre-configured functions for a simple integration into AdComNet networks; Fully integrated fledged line for the connection of smoke detectors and/or smoke vent buttons; Manual input signal triggering because of integrated buttons;   Technical data: Power supply: 24 V DC Current consumption: max. 200 mA - 1 Main interface - 1 Sub interface - 1 SHEV-line - 8 digital inputs - 8 digital bistable outputs (two-way contacts) Dimensions (WxHxD): 157 x 115 x 59 mm   Scope of supply: I/O module, bus terminal clamps, 2 pcs. terminal module line   Brand: D+H Mechatronic AG Type: ACN-IO501   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.553.80 1.1.122 Connection module - ACN-CM501 for RZN 44xx-M   Performance features: Pluggable module for the connection of RZN 44xx-M smoke vent control panels; Passing on smoke control and ventilation commands as well as decentralised control commands; Galvanically isolated connection of the AdComNet bus system and the control panel; Integrated router and repeater; Functionality within and below the segment stay intact in case of fault of another segment; Supply voltage is provided by the smoke control panel; No additional capacity of the accumulator for the control panel is needed.   Technical data: Power supply: 24 V DC Current consumption: max. 5 mA - 1 master interface - 1 slave interface - Terminal clamp with elastic force twin-connection for 0.12 mm² - 0.5 mm² Dimensions (WxHxD): 53 x 59 x 27 mm   Scope of supply: Connection module, bus terminal clamps, bus terminators   Brand: D+H Mechatronic AG Type: ACN-CM501   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.553.60 1.1.123 Modbus-Gateway - ACN-GW501-MRTU-0200 for integrating AdComNet in Modbus networks   Performance features: Universal gateway to Modbus networks; Integrated AdComNet router and repeater; In case of defect in another segment the functionalities within & below the segment stay intact; Simple integration into AdComNet networks;   Technical data: Supply: 24 V DC / ±20 % Input power: < 1 W Modbus protocol: MODBUS RTU Modbus interface: RS 485 data points: 400 AdComNet-Master: 1x AdComNet-Slave: 1x Housing material: bottom part = PPO / top part = PC Type of protection: IP40 Temperature range: - 10 °C till 80 °C Connection: Pluggable terminal Installation: Top hat rail TS 35 Dimensions (WxHxD): 86 x 52 x 58 mm   Brand: D+H Mechatronic AG Type: ACN-GW501-MRTU-0200   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.554.20 1.1.124 Remote maintenance gateway - RM-GW-ETH For remote maintenance of CPS-M or RZN (ACN-BI501-USB with ACN-CM501) via USB   Performance features: 2 digital inputs for fault, alarm or remote access release; Central administration and control via the D+H Software SCS; E-mail notification in case of malfunction or alarm, individually adjustable per device; Automatic firmware updates of the gateway; Connection via USB A-B cable;   Technical data: Supply: 24 V DC Input power: 1.2 A max. Material housing: Plastic Type of protection: IP 20 Temperature range: 0 °C till +50 °C Connection: Pluggable terminal, USB-connections Installation: Top hat rail TS 35 Dimensions (WxHxD): 107 x 95 x 58 mm   Brand: D+H Mechatronic AG Type: RM-GW-ETH   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.555.30 1.1.125 SHEV operation panel - RT 46, orange Surface-mounted   Performance features: Operation panel for manually triggering a SHEV system in case of fire; Operation panel developed according to pr EN 12101-9 and VdS 2592; Elegant plastic housing with high surface quality; Can be used as main or auxiliary control panel;   Functions: - SHEV OPEN, SHEV Reset   Display: - Operational standby - SHEV alarm triggered - Fault indication   Technical data: Supply: 24 V DC (18 - 28 V DC) Type of protection: IP 40 Temperature range: -5 °C till +40 °C Housing: Die-cast aluminium (surface-mounted housing) Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 128 x 134.5 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT 46   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.442.10 1.1.126 SHEV operation panel - RT 46-ALU/Y, yellow Surface-mounted   Performance features: Operation panel for manually triggering a SHEV system in case of fire; Operation panel developed according to pr EN 12101-9 and VdS 2592; Shapely and extremely robust aluminium housing; Can be used as main or auxiliary control panel;   Functions: - SHEV OPEN, SHEV Reset   Display: - Operational standby - SHEV alarm triggered - Fault indication   Technical data: Supply: 24 V DC (18 - 28 V DC) Type of protection: IP 40 Temperature range: -5 °C till +40 °C Housing: Die-cast aluminium (surface-mounted housing) Colour: Yellow (~ RAL 1004) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT 46-ALU/Y   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.442.20 1.1.127 RT housing - RT GEH03, orange Surface-mounted   Performance features: For SHEV operation panel; Elegant plastic housing with high surface quality; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 128 x 134,5 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH03   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.442.35 1.1.128 RT housing - RT GEH02-ALU, orange Surface-mounted   Performance features: For SHEV operation panel; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-ALU   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.33 1.1.129 RT housing - RT GEH02-ALU/B, blue Surface-mounted   Performance features: For SHEV operation panel; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Blue (~ RAL 5009) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-ALU/B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.36 1.1.130 RT housing - RT GEH02-ALU/G, grey Surface-mounted   Performance features: For SHEV operation panel; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Grey (~ RAL 7035) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-ALU/G   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.34 1.1.131 RT housing - RT GEH02-ALU/R, red Surface-mounted   Performance features: For SHEV operation panel; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Red (~ RAL 3000) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-ALU/R   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.35 1.1.132 RT housing - RT GEH02-ALU/Y, yellow Surface-mounted   Performance features: For SHEV operation panel; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Yellow (~ RAL 1004) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-ALU/Y   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.37 1.1.133 RT housing - RT GEH03-LT, orange With cut-out for ventilation button operation unit Surface-mounted   Performance features: For SHEV operation panel with ventilation button; Elegant plastic housing with high surface quality; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 128 x 134,5 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH03-LT   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.442.40 1.1.134 RT housing - RT GEH02-LT-ALU, orange With cut-out for ventilation button operation unit Surface-mounted   Performance features: For SHEV operation panel with ventilation button; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Orange (~ RAL 2011) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-LT-ALU   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.38 1.1.135 RT housing - RT GEH02-LT-ALU/B, blue With cut-out for ventilation button operation unit Surface-mounted   Performance features: For SHEV operation panel with ventilation button; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Blue (~ RAL 5009) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-LT-ALU/B   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.41 1.1.136 RT housing - RT GEH02-LT-ALU/G, grey With cut-out for ventilation button operation unit Surface-mounted   Performance features: For SHEV operation panel with ventilation button; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Grey (~ RAL 7035) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-LT-ALU/G   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.39 1.1.137 RT housing - RT GEH02-LT-ALU/R, red With cut-out for ventilation button operation unit Surface-mounted   Performance features: For SHEV operation panel with ventilation button; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Red (~ RAL 3000) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-LT-ALU/R   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.40 1.1.138 RT housing - RT GEH02-LT-ALU/Y, yellow With cut-out for ventilation button operation unit Surface-mounted   Performance features: For SHEV operation panel with ventilation button; Shapely and extremely robust aluminium housing; Operation units must be ordered separately;   Technical data: Housing: Die-cast aluminium (surface-mounted housing) Colour: Yellow (~ RAL 1004) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT GEH02-LT-ALU/Y   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 65.403.42 1.1.139 RT ventilation button operation unit - RT LT45 for SHEV operation panel RT-LT   Performance features: For SHEV operation panel with ventilation button;   Functions: - Ventilation OPEN, Ventilation CLOSED   Display: - Ventilation OPEN   Technical data: Supply: 24 V DC (18 - 28 V DC) Dimensions (WxH): 88 x 25 mm   Scope of supply: Operation panel   Brand: D+H Mechatronic AG Type: RT LT45   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.420.36 1.1.140 RT operation unit - RT BE46-1 for SHEV operation panel of the RT 45 and RT 46 Series, (single)   Performance features: For SHEV triggering one fire/smoke compartment; Can be used as main or auxiliary control panel;   Functions: - SHEV OPEN, SHEV Reset   Display: - Operational standby - SHEV alarm triggered - Fault indication   Technical data: Supply: 24 V DC (18 - 28 V DC) Temperature range: -5 °C till +40 °C Dimensions (WxH): 105 x 115 mm   Scope of supply: Operation unit with circuit board holder   Brand: D+H Mechatronic AG Type: RT BE46-1   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.442.25 1.1.141 RT operation unit - RT BE46-1-LT for SHEV operation panel of the RT 45 and RT 46 Series, (single) with ventilation button   Performance features: For SHEV triggering one fire/smoke compartment; Can be used as main or auxiliary control panel;   Functions: - SHEV OPEN, SHEV Reset - Ventilation OPEN, Ventilation CLOSED   Display: - Operational standby - SHEV alarm triggered - Fault indication   Technical data: Supply: 24 V DC (18 - 28 V DC) Temperature range: -5 °C till +40 °C Dimensions (WxH): 105 x 115 mm   Scope of supply: Operation unit with circuit board holder   Brand: D+H Mechatronic AG Type: RT BE46-1-LT   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.442.30 1.1.142 RT operation unit - RT BE45-2 for SHEV operation panel RT, (double)   Performance features: For SHEV triggering 2 separate fire/smoke compartments; Can be used as main or auxiliary control panel;   Functions: - SHEV area 1 OPEN, SHEV area 1 reset - SHEV area 2 OPEN, SHEV area 2 reset   Display: - Operational standby - SHEV alarm area 1 triggered - SHEV alarm area 2 triggered   Technical data: Supply: 24 V DC (18 - 28 V DC) Temperature range: -5 °C till +40 °C Dimensions (WxH): 105 x 115 mm   Scope of supply: Operation unit with circuit board holder   Brand: D+H Mechatronic AG Type: RT BE45-2   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.451.60 1.1.143 RT operation unit - RT BE45-3 for SHEV operation panel RT, (tripple)   Performance features: For SHEV triggering 3 separate fire/smoke compartments; Can be used as main or auxiliary control panel;   Functions: - SHEV area 1 OPEN, SHEV area 1 reset - SHEV area 2 OPEN, SHEV area 2 reset - SHEV area 3 OPEN, SHEV area 3 reset   Display: - Operational standby - SHEV alarm area 1 triggered - SHEV alarm area 2 triggered - SHEV alarm area 3 triggered   Technical data: Supply: 24 V DC (18 - 28 V DC) Temperature range: -5 °C till +40 °C Dimensions (WxH): 105 x 115 mm   Scope of supply: Operation unit with circuit board holder   Brand: D+H Mechatronic AG Type: RT BE45-3   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.451.70 1.1.144 RT operation unit - RT BE42-ST for SHEV operation panel RT, with acoustic fault signal   Performance features: For SHEV operation panel;   Functions: - SHEV OPEN, SHEV Reset, acoustic signal - Operational standby ON / OFF   Display: - Operational standby - SHEV alarm triggered - Fault indication - Indicator diode blinks for SHEV alarm if acoustic signal is not operational   Acoustic signal: - for SHEV alarm (in operational standby ON modus)   Technical data: Supply: 24 V DC (18 - 28 V DC) Loudness: 75 dB Temperature range: -5 °C till +40 °C Dimensions (WxH): 105 x 115 mm   Scope of supply: Operation unit with circuit board holder   Brand: D+H Mechatronic AG Type RT BE42-ST   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.435.12 1.1.145 RT operation unit - RT BE42-Z for SHEV operation panel RT, 2-wire, with indicator   Performance features: For SHEV operation panel; For 2-wire cables; Can be used only in conjunction with standard SHEV operation panel and UM 41 transfer module;   Functions: - SHEV OPEN   Anzeigen: - Operational standby - Alarm triggered   Technical data: Supply: 24 V DC (18 - 28 V DC) Temperature range: -5 °C till +40 °C Dimensions (WxH): 105 x 115 mm   Scope of supply: Operation unit with circuit board holder   Brand: D+H Mechatronic AG Type: RT BE42-Z   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.435.62 1.1.146 RT operation unit - RT BE42-Z-K for SHEV operation panel RT, 2-wire, without indicator   Performance features: For SHEV operation panel; For 2-wire cables; Can be used only in conjunction with standard SHEV operation panel and UM 41 transfer module;   Functions: - SHEV OPEN   Anzeigen: - Operational standby - Alarm triggered   Technical data: Supply: 24 V DC (18 - 28 V DC) Temperature range: -5 °C till +40 °C Dimensions (WxH): 105 x 115 mm   Scope of supply: Operation unit with circuit board holder   Brand: D+H Mechatronic AG Type: RT BE42-Z-K   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.435.64 1.1.147 RT flush-mounted frame - RT UPR 02, orange Cover frame for RT 45 flush-mounting   Performance features: Cover frame for flush-mounted installation of the RT 45/-LT;   Technical data: Material: Aluminium Colour: Orange (~ RAL 2011) Dimensions (WxH): 170 x 180 mm   Scope of supply: Flush-mounted frame, mounting screws   Brand: D+H Mechatronic AG Type: RT UPR 02   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 68.104.43 1.1.148 RT flush-mounted frame - RT UPR 02/G, grey Cover frame for RT 45 flush-mounting   Performance features: Cover frame for flush-mounted installation of the RT 45/-LT;   Technical data: Material: Aluminium Colour: Grey (~ RAL 7035) Dimensions (WxH): 170 x 180 mm   Scope of supply: Flush-mounted frame, mounting screws   Brand: D+H Mechatronic AG Type: RT UPR 02/G   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 68.104.44 1.1.149 RT flush-mounted socket - RT UPD 02 Flush-mounted socket for RT 45   Performance features: Installation socket for flush-mounted installation of a RT 45/-LT; Designed für installation in hollow, stone and concrete walls;   Technical data: Material: Plastic Dimensions (WxHxD): 220 x 155 x 50 mm   Scope of supply : Flush-mounted socket, cover for flush-mounted installation, fixing clamps   Brand: D+H Mechatronic AG Type: RT UPD 02   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 66.103.77 1.1.150 Emergency hammer - EH 401 Use a hammer to break glass pane in case of an alarm   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.110.25 1.1.151 SHEV operation panel - RT 45/R-FR, red Surface-mounted   Performance features: For 24 V DC D+H smoke vent control panels with NF approval; Operation panel for manually triggering a SHEV system in case of fire; Operation panel developed according to pr EN 12101-9 and VdS 2592; Shapely and extremely robust aluminium housing; Can be used as main or auxiliary control panel;   Function: - SHEV OPEN   Technical data: Supply: 24 V DC (18 - 28 V DC) Type of protection: IP 40 Temperature range: -5 °C till +40 °C Housing: Die-cast aluminium (surface-mounted housing) Colour: Red (~ RAL 3000) Dimensions (WxHxD): 129 x 138 x 39 mm   Scope of supply: Lockable housing with operation unit, break-type glass, key, designation labels in 32 languages   Brand: D+H Mechatronic AG Type: RT 45/R-FR   Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes) Unit : Stk Artikelnr. : 30.439.10 1.1.152 Acoustic signal emitter - CWSO-RR-S1 VdS approved, 32 sounds selectable   Performance features: Acoustic signal emitter in accordance with EN 54-3; 32 different sounds can be programmed; Optional connection for activating a second sound; Synchronous sound output; Volume can be set in 2 levels on the device; VdS approval number: G 215015;   Technical data: Supply: 9 - 29 V DC / 0.03 A Loudness: 102.1 dB Type of protection: IP 21C Colour: Red (~ RAL 3020) Dimensions (WxD): 77 x 100 mm   Scope of supply: Signal emitter, instruction for use   Brand: D+H Mechatronic AG Type: CWSO-RR-S1   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 30.301.55 1.1.153 Battery - Akku Typ 1 Battery 12 V / 1.2 Ah ±15 % Approved by VdS   Performance features: Accumulators for 72 hours of emergency power supply of D+H control panels integrated into housing.   Technical data: Voltage: 12 V DC Battery capacity: 1.2 Ah ±15 % Dimensions (WxHxD): approx. 97 x 53 x 43 mm   Scope of supply: 1 Single pack (1 Battery)   Brand: D+H Mechatronic AG Type: Akku Typ 1   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 70.200.04 1.1.154 Battery - Akku Typ 2 Battery 12 V / 2.2 Ah ±15 % Approved by VdS   Performance features: Accumulators for 72 hours of emergency power supply of D+H control panels integrated into housing.   Technical data: Voltage: 12 V DC Battery capacity: 2.2 Ah ±15 % Dimensions (WxHxD): approx. 178 x 66 x 34 mm   Scope of supply: 1 Single pack (1 Battery)   Brand: D+H Mechatronic AG Type: Akku Typ 2   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 70.200.01 1.1.155 Battery - Akku Typ 3 Battery 12 V / 7 Ah ±15 % Approved by VdS   Performance features: Accumulators for 72 hours of emergency power supply of D+H control panels integrated into housing.   Technical data: Voltage: 12 V DC Battery capacity: 7 Ah ±15 % Dimensions (WxHxD): approx. 151 x 102 x 65 mm   Scope of supply: 1 Single pack (1 Battery)   Brand: D+H Mechatronic AG Type: Akku Typ 3   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 70.200.02 1.1.156 Battery - Akku Typ 4 Battery 12 V / 12 Ah ±15 % Approved by VdS   Performance features: Accumulators for 72 hours of emergency power supply of D+H control panels integrated into housing.   Technical data: Voltage: 12 V DC Battery capacity: 12 Ah ±15 % Dimensions (WxHxD): approx. 151 x 100 x 99 mm   Scope of supply: 1 Single pack (1 Battery)   Brand: D+H Mechatronic AG Type: Akku Typ 4   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 70.200.00 1.1.157 Battery - Akku Typ 5 Battery 12 V / 18 Ah ±15 % Approved by VdS   Performance features: Accumulators for 72 hours of emergency power supply of D+H control panels integrated into housing.   Technical data: Voltage: 12 V DC Battery capacity: 18 Ah ±15 % Dimensions (WxHxD): approx. 181 x 167 x 76 mm   Scope of supply: 1 Single pack (1 Battery)   Brand: D+H Mechatronic AG Type: Akku Typ 5   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 70.200.05 1.1.158 Battery - Akku Typ 6 Battery 12 V / 26 Ah ±15 % Approved by VdS   Performance features: Accumulators for 72 hours of emergency power supply of D+H control panels integrated into housing.   Technical data: Voltage: 12 V DC Battery capacity: 26 Ah ±15 % Dimensions (WxHxD): approx. 166 x 125 x 175 mm   Scope of supply: 1 Single pack (1 Battery)   Brand: D+H Mechatronic AG Type: Akku Typ 6   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 70.200.03 1.1.159 Battery - Akku Typ 8 Battery 12 V / 3.4 Ah ±15 % Approved by VdS   Performance features: Accumulators for 72 hours of emergency power supply of D+H control panels integrated into housing.   Technical data: Voltage: 12 V DC Battery capacity: 3.4 Ah ±15 % Dimensions (WxHxD): approx. 134 x 66 x 67 mm   Scope of supply: 1 Single pack (1 Battery)   Brand: D+H Mechatronic AG Type: Akku Typ 8   Planning Support (https://www.dh-partner.com/int/en/service/planning-support) Unit : Stk Artikelnr. : 70.200.12