1	D+H Mechatronic (english)
1.1	Rack and pinion drives
Information on power-operated windows

When manufacturing and operating power-operated opening elements, the applicable safety regulations must be observed. A risk assessment in accordance with the Machinery Directive 2006/42/EEC must be carried out by the manufacturer with the introduction of the product standard DIN EN 1453-1 and documented on the power-operated window by means of an EC Declaration of Conformity and the CE marking.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)
Information on bracket technology

For special solutions and CAD sections of the brackets, please contact your local project consultant.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)
Information Selection Guide

Technologie LIGHT (K)
LIGHT actuators (230 V AC) can only be controlled in OPEN and CLOSE direction.
 
 
Technologie PLP
Data transmission via the drive‘s connection cable. Drive characteristics can be programmed directly via the supply cable. Thus, no additional cable is required for parameterisation.
 
 
Technologie BSY+
BSY+ enables communication and synchronisation between different components in the window. For example between the chain drives, during synchronous operation, or between window and locking drives (e.g. FRA 11 BSY+ or VLD-BSY+). 
 
 
Technologie ACB
Enables direct bus communication between the controller and the drive for, for example, control with perfect positioning or drive feedback. Communication is via the open source Modbus protocol, and it enables the drive to be combined with an ACB?capable control panel or enables it to be directly connected to higher-level controllers such as a building management system.
1.1.1	PLP rack and pinion drive - ZA-0300-0350-1-PLP-R
24 V DC / 0.5 A / 300 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0350-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.05

1.1.2	PLP rack and pinion drive - ZA-0300-0500-1-PLP-R
24 V DC / 0.5 A / 300 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0500-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.10

1.1.3	PLP rack and pinion drive - ZA-0300-0600-1-PLP-R
24 V DC / 0.5 A / 300 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0600-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.15

1.1.4	PLP rack and pinion drive - ZA-0300-0800-1-PLP-R
24 V DC / 0.5 A / 300 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0800-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.5	PLP rack and pinion drive - ZA-0300-1000-1-PLP-R
24 V DC / 0.5 A / 300 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-1000-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.6	PLP rack and pinion drive - ZA-0800-0350-1-PLP-R
24 V DC / 1 A / 800 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0350-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.30

1.1.7	PLP rack and pinion drive - ZA-0800-0500-1-PLP-R
24 V DC / 1 A / 800 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0500-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.35

1.1.8	PLP rack and pinion drive - ZA-0800-0600-1-PLP-R
24 V DC / 1 A / 800 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0600-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.40

1.1.9	PLP rack and pinion drive - ZA-0800-0800-1-PLP-R
24 V DC / 1 A / 800 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0800-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.45

1.1.10	PLP rack and pinion drive - ZA-0800-1000-1-PLP-R
24 V DC / 1 A / 800 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-01000-1-PLP-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.50

1.1.11	PLP rack and pinion drive - ZA-1000-0350-1-PLP-R
24 V DC / 1.2 A / 1000 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0350-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.12	PLP rack and pinion drive - ZA-1000-0500-1-PLP-R
24 V DC / 1.2 A / 1000 N / 500 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0500-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.13	PLP rack and pinion drive - ZA-1000-0600-1-PLP-R
24 V DC / 1.2 A / 1000 N / 600 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0600-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.14	PLP rack and pinion drive - ZA-1000-0800-1-PLP-R
24 V DC / 1.2 A / 1000 N / 800 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0800-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.15	PLP rack and pinion drive - ZA-1000-1000-1-PLP-R
24 V DC / 1.2 A / 1000 N / 100 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-1000-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.16	PLP rack and pinion drive - ZA-1500-0350-1-PLP-R
24 V DC / 1.4 A / 1500 N / 350 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0350-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.17	PLP rack and pinion drive - ZA-1500-0500-1-PLP-R
24 V DC / 1.4 A / 1500 N / 500 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0500-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.18	PLP rack and pinion drive - ZA-1500-0600-1-PLP-R
24 V DC / 1.4 A / 1500 N / 600 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0600-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.19	PLP rack and pinion drive - ZA-1500-0800-1-PLP-R
24 V DC / 1.4 A / 1500 N / 800 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0800-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.20	PLP rack and pinion drive - ZA-1500-1000-PLP-R
24 V DC / 1.4 A / 1500 N / 1000 mm Hub
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-1000-1-PLP-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.21	PLP rack and pinion drive - ZA-1-PLP - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for opening and closing of windows, flaps and skylights. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions (stroke limitation, force, speed) and performance features on site via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV) (optional). Particularly quiet drive in ventilation mode due to reduced running speed. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption:
0.5 A (ZA-0300-1-PLP) (1.2 A with HS)
1 A (ZA-0800-1-PLP) (2 A with HS)
1.2 A (ZA-1000-1-PLP) (2.2 A with HS)
1.4 A (ZA-1500-1-PLP) (2.5 A with HS)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
300 N (ZA-0300-1-PLP)
800 N (ZA-0800-1-PLP)
1000 N (ZA-1000-1-PLP)
1500 N (ZA-1500-1-PLP)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (ZA-0300-1-PLP)
800 N (ZA-0800-1-PLP)
1000 N (ZA-1000-1-PLP)
1000 N (ZA-1500-1-PLP)
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 100 mm - 1500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
OPEN running speed - HS: 17 mm/
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level:
LpA ≤ 51 dB(A)
LpA ≤ 60.5 dB(A) (with HS)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium
Colour: on request
Housing motor: Polycarbonate
Colour. on request
Connection: Silicone cable
Dimensions (WxHxD):
Tube 225-1662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1-PLP
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.005.00

1.1.22	Extension functions ZA-PLP
	Option "HS" -High-Speed option for SHEV application possible
	Option "OT" -Reduced swivel range by omitting the tube
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "BRV" -Signal for connection to FRA, VLD, ERM 44 or AT 41
	Option "W" -Weatherproof for outdoor use
	Option "WS" -Swimming pool protected for use in swimming pools
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.23	ACB rack and pinion drive - ZA-0300-0350-1-ACB M1-R
24 V DC / 0.5 A / 300 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0350-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.24	ACB rack and pinion drive - ZA-0300-0350-1-ACB M2-R
24 V DC / 0.5 A / 300 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0350-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.25	ACB rack and pinion drive - ZA-0300-0350-1-ACB S1-L
24 V DC / 0.5 A / 300 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0350-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.26	ACB rack and pinion drive - ZA-0300-0500-1-ACB M1-R
24 V DC / 0.5 A / 300 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0500-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.27	ACB rack and pinion drive - ZA-0300-0500-1-ACB M2-R
24 V DC / 0.5 A / 300 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0500-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.28	ACB rack and pinion drive - ZA-0300-0500-1-ACB S1-L
24 V DC / 0.5 A / 300 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0500-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.29	ACB rack and pinion drive - ZA-0300-0600-1-ACB M1-R
24 V DC / 0.5 A / 300 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0600-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.30	ACB rack and pinion drive - ZA-0300-0600-1-ACB M2-R
24 V DC / 0.5 A / 300 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
* For vertical use, please consult with D+H Sales!
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0600-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.31	ACB rack and pinion drive - ZA-0300-0600-1-ACB S1-L
24 V DC / 0.5 A / 300 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0600-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.32	ACB rack and pinion drive - ZA-0300-0800-1-ACB M1-R
24 V DC / 0.5 A / 300 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0800-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.33	ACB rack and pinion drive - ZA-0300-0800-1-ACB M2-R
24 V DC / 0.5 A / 300 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0800-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.34	ACB rack and pinion drive - ZA-0300-0800-1-ACB S1-L
24 V DC / 0.5 A / 300 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Links
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-0800-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.35	ACB rack and pinion drive - ZA-0300-1000-1-ACB M1-R
24 V DC / 0.5 A / 300 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-1000-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.36	ACB rack and pinion drive - ZA-0300-1000-1-ACB M2-R
24 V DC / 0.5 A / 300 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-1000-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.37	ACB rack and pinion drive - ZA-0300-1000-1-ACB S1-L
24 V DC / 0.5 A / 300 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0300-1000-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.38	ACB rack and pinion drive - ZA-0800-0350-1-ACB M1-R
24 V DC / 1 A / 800 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0350-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.39	ACB rack and pinion drive - ZA-0800-0350-1-ACB M2-R
24 V DC / 1 A / 800 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0350-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.40	ACB rack and pinion drive - ZA-0800-0350-1-ACB S1-L
24 V DC / 1 A / 800 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0350-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.41	ACB rack and pinion drive - ZA-0800-0500-1-ACB M1-R
24 V DC / 1 A / 800 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0500-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.05

1.1.42	ACB rack and pinion drive - ZA-0800-0500-1-ACB M2-R
24 V DC / 1 A / 800 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0500-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.25

1.1.43	ACB rack and pinion drive - ZA-0800-0500-1-ACB S1-L
24 V DC / 1 A / 800 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0500-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.45

1.1.44	ACB rack and pinion drive - ZA-0800-0600-1-ACB M1-R
24 V DC / 1 A / 800 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0600-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.10

1.1.45	ACB rack and pinion drive - ZA-0800-0600-1-ACB M2-R
24 V DC / 1 A / 800 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0600-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.30

1.1.46	ACB rack and pinion drive - ZA-0800-0600-1-ACB S1-L
24 V DC / 1 A / 800 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0600-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.50

1.1.47	ACB rack and pinion drive - ZA-0800-0800-1-ACB M1-R
24 V DC / 1 A / 800 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0800-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.15

1.1.48	ACB rack and pinion drive - ZA-0800-0800-1-ACB M2-R
24 V DC / 1 A / 800 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0800-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.35

1.1.49	ACB rack and pinion drive - ZA-0800-0800-1-ACB S1-L
24 V DC / 1 A / 800 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-0800-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.55

1.1.50	ACB rack and pinion drive - ZA-0800-1000-1-ACB M1-R
24 V DC / 1 A / 800 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-1000-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.20

1.1.51	ACB rack and pinion drive - ZA-0800-1000-1-ACB M2-R
24 V DC / 1 A / 800 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-1000-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.40

1.1.52	ACB rack and pinion drive - ZA-0800-1000-1-ACB S1-L
24 V DC / 1 A / 800 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Links
Force of pressure: 800 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 800 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm, housing motor 160 x 104 x 46 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-0800-1000-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.60

1.1.53	ACB rack and pinion drive - ZA-1000-0350-1-ACB M1-R
24 V DC / 1.2 A / 1000 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0350-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.54	ACB rack and pinion drive - ZA-1000-0350-1-ACB M2-R
24 V DC / 1.2 A / 1000 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0350-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.55	ACB rack and pinion drive - ZA-1000-0350-1-ACB S1-L
24 V DC / 1.2 A / 1000 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0350-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.56	ACB rack and pinion drive - ZA-1000-0500-1-ACB M1-R
24 V DC / 1.2 A / 1000 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0500-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.57	ACB rack and pinion drive - ZA-1000-0500-1-ACB M2-R
24 V DC / 1.2 A / 1000 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0500-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.58	ACB rack and pinion drive - ZA-1000-0500-1-ACB S1-L
24 V DC / 1.2 A / 1000 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0500-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.59	ACB rack and pinion drive - ZA-1000-0600-1-ACB M1-R
24 V DC / 1.2 A / 1000 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0600-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.60	ACB rack and pinion drive - ZA-1000-0600-1-ACB M2-R
24 V DC / 1.2 A / 1000 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0600-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.61	ACB rack and pinion drive - ZA-1000-0600-1-ACB S1-L
24 V DC / 1.2 A / 1000 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design:Left
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0600-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.62	ACB rack and pinion drive - ZA-1000-0800-1-ACB M1-R
24 V DC / 1.2 A / 1000 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0800-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.63	ACB rack and pinion drive - ZA-1000-0800-1-ACB M2-R
24 V DC / 1.2 A / 1000 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0800-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.64	ACB rack and pinion drive - ZA-1000-0800-1-ACB S1-L
24 V DC / 1.2 A / 1000 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-0800-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.65	ACB rack and pinion drive - ZA-1000-1000-1-ACB M1-R
24 V DC / 1.2 A / 1000 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-1000-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.66	ACB rack and pinion drive - ZA-1000-1000-1-ACB M2-R
24 V DC / 1.2 A / 1000 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-1000-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.67	ACB rack and pinion drive - ZA-1000-1000-1-ACB S1-L
24 V DC / 1.2 A / 1000 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1000-1000-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.68	ACB rack and pinion drive - ZA-1500-0350-1-ACB M1-R
24 V DC / 1.4 A / 1500 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0350-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.69	ACB rack and pinion drive - ZA-1500-0350-1-ACB M2-R
24 V DC / 1.4 A / 1500 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0350-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.70	ACB rack and pinion drive - ZA-1500-0350-1-ACB S1-L
24 V DC / 1.4 A / 1500 N / 350 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0350-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.71	ACB rack and pinion drive - ZA-1500-0500-1-ACB M1-R
24 V DC / 1.4 A / 1500 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0500-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.72	ACB rack and pinion drive - ZA-1500-0500-1-ACB M2-R
24 V DC / 1.4 A / 1500 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0500-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.73	ACB rack and pinion drive - ZA-1500-0500-1-ACB S1-L
24 V DC / 1.4 A / 1500 N / 500 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle:Current consumption: 1.4 A 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0500-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.74	ACB rack and pinion drive - ZA-1500-0600-1-ACB M1-R
24 V DC / 1.4 A / 1500 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 772 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0600-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.75	ACB rack and pinion drive - ZA-1500-0600-1-ACB M2-R
24 V DC / 1.4 A / 1500 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 772 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0600-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.76	ACB rack and pinion drive - ZA-1500-0600-1-ACB S1-L
24 V DC / 1.4 A / 1500 N / 600 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0600-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.77	ACB rack and pinion drive - ZA-1500-0800-1-ACB M1-R
24 V DC / 1.4 A / 1500 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0800-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.78	ACB rack and pinion drive - ZA-1500-0800-1-ACB M2-R
24 V DC / 1.4 A / 1500 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0800-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.79	ACB rack and pinion drive - ZA-1500-0800-1-ACB S1-L
24 V DC / 1.4 A / 1500 N / 800 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-0800-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.80	ACB rack and pinion drive - ZA-1500-1000-1-ACB M1-R
24 V DC / 1.4 A / 1500 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-1000-1-ACB M1-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.81	ACB rack and pinion drive - ZA-1500-1000-1-ACB M2-R
24 V DC / 1.4 A / 1500 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-1000-1-ACB M2-R
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.82	ACB rack and pinion drive - ZA-1500-1000-1-ACB S1-L
24 V DC / 1.4 A / 1500 N / 1000 mm stroke
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Slave1
Design: Left
Force of pressure: 1500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 100 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
CLOSED running speed: separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 1162 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1500-1000-1-ACB S1-L
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.83	ACB rack and pinion drive - ZA-1-ACB - freely configurable
24 V DC / Special production according to customer requirements
 
Electromotive drive unit for convenient opening and closing of bottom hung-, top hung- and trapezoidal windows, flaps and skylights with high weights. Useable for smoke exhaust, D+H Euro-SHEV according to DIN EN 12101-2 as well as daily natural ventilation.
 
Performance features:
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Rack and pinion drives equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of the rack and pinion drives at a window;
High-precision synchron-electronic for parallel run for up to 8 drives with the option to link with up to 4 lock drives;
Sustains the application at trapezoidal windows with up to 4 rack and pinion drives in one drive group;
Enchased drive unit;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV) (optional);
Electronic limit stop and overload cut-off;
Various drive functions and drive parameters (stroke limitation, force, speed) via D+H software SCS programmable;
Extra silent motor running in ventilation mode because of reduced running speed;
Cable entry possible at top or bottom;
Drive unit changeable from left to right;
Service life > 20000 strokes in case of ventilation;
 
Functional description ACB
Secure SHEV-Bus communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives. realisation of simultaneous control commands in various drive groups by group linking.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption:
0.5 A (ZA-0300-1-ACB) (1.2 A with HS)
1 A (ZA-0800-1-ACB) (2 A with HS)
1.2 A (ZA-1000-1-ACB) (2.2 A with HS)
1.4 A (ZA-1500-1-ACB) (2.5 A with HS)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Design: Right or left
Force of pressure:
300 N (ZA-0300-1-ACB)
800 N (ZA-0800-1-ACB)
1000 N (ZA-1000-1-ACB)
1500 N (ZA-1500-1-ACB)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (ZA-0300-1-ACB)
800 N (ZA-0800-1-ACB)
1000 N (ZA-1000-1-ACB)
1000 N (ZA-1500-1-ACB)
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 100 mm - 1500 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 7 mm/s
OPEN running speed - HS: 17 mm/s
CLOSED running speed: Separated, according to close section from 7 mm/s to 5 mm/s
Type of protection: IP 65
Emission sound pressure level:
LpA ≤ 51 dB(A)
LpA ≤ 60.5 dB(A) (with HS)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium
Colour: on request
Housing motor: Polycarbonate
Colour: on request
Connection: Silicone cable
Dimensions (WxHxD):
Tube 225-1662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-1-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.011.00

1.1.84	Extension functions ZA-1-ACB
	Option "HS" -High-Speed option for SHEV application possible
	Option "OT" -Reduced swivel range by omitting the tube
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED"
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "W" -Weatherproof for outdoor use
	Option "WS" -Swimming pool protected for use in swimming pools
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.85	BSY+ rack and pinion drive - ZA-K-BSY+ - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV) (optional). Direct control via 230 V AC. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive functions and different drive parameters are pre-installed at the factory or individually programmable via the D+H software SCS.Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance:
20 W / 30 VA (ZA 35-K-BSY+) (35 W / 45 VA bei HS)
30 W / 45 VA (ZA 85-K-BSY+) (50 W / 75 VA bei HS)
35 W / 55 VA (ZA 105-K-BSY+) (60 W / 85 VA bei HS)
45 W / 70 VA (ZA 155-K-BSY+) (75 W / 105 VA bei HS)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main or Sub
Design: Right or left
Force of pressure:
300 N (ZA 35-K-BSY+)
800 N (ZA 85-K-BSY+)
1000 N (ZA 105-K-BSY+)
1500 N (ZA 155-K-BSY+)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (ZA 35-K-BSY+)
800 N (ZA 85-K-BSY+)
1000 N (ZA 105-K-BSY+)
1000 N (ZA 155-K-BSY+)
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 100 mm - 1500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
OPEN running speed - HS: 17 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 65
Emission sound pressure level:
LpA ≤ 51 dB(A)
LpA ≤ 60.5 dB(A) (with HS)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube Aluminium,
Colour: on request
Housing motor: Polycarbonate
Colour: on request
Connection: Silicone cable
Dimensions (WxHxD):
Tube 225-1662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.007.01

1.1.86	Extension functions ZA-K-BSY+
	Option "HS" -High-Speed option for SHEV application possible
	Option "OT" -Reduced swivel range by omitting the tube
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "W" -Weatherproof for outdoor use
	Option "WS" -Swimming pool protected for use in swimming pools
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.87	Rack and pinion drive - ZA 105/350-K
230 V AC / 30 VA / 1000 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Direct control via 230 V AC. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 27 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 350 mm
OPEN running speed: 10 mm/s
CLOSED running speed: 10 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Housing tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 512 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA 105/350-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.007.05

1.1.88	Rack and pinion drive - ZA 105/500-K
230 V AC / 30 VA / 1000 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Direct control via 230 V AC. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 27 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 500 mm
OPEN running speed: 10 mm/s
CLOSED running speed: 10 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Housing tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA 105/500-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.007.10

1.1.89	Rack and pinion drive - ZA 105/600-K
230 V AC / 30 VA / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Direct control via 230 V AC. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 27 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 600 mm
OPEN running speed: 10 mm/s
CLOSED running speed: 10 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Housing tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 762 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
* For vertical use, please consult with D+H Sales!
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA 105/600-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.90	Rack and pinion drive - ZA 105/800-K
230 V AC / 30 VA / 1000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Direct control via 230 V AC. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 27 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 800 mm
OPEN running speed: 10 mm/s
CLOSED running speed: 10 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Housing tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
Dimensions (WxHxD):
Tube 962 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA 105/800-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.007.15

1.1.91	Rack and pinion drive - ZA 105/1000-K
230 V AC / 30 VA / 1000 N / 1000 mm Hub
 
Leistungsmerkmale:
Elektromotorische Antriebseinheit für die Montage auf dem Fensterrahmenprofil oder Flügelprofil. Antrieb zum elektromotorischen Öffnen- und Schließen von Fenstern, Klappen und Lichtkuppeln. Der Antrieb ist einsetzbar für Öffnungen zur Rauchableitung, D+H Euro-RWA gemäß DIN EN12101-2 sowie für tägliche Lüftung. Ansteuerung erfolgt direkt über 230 V AC. Antrieb ist besonders leise im täglichen Lüftungsbetrieb. Eine elektronische End- und Überlastabschaltung schützt das Element und den Antrieb vor Schäden. Die Stromversorgung ist wahlweise von unten oder oben anschließbar. Ebenso ist die Antriebseinheit von links auf rechts wechselbar.
 
Technische Daten:
Betriebsspannung: 230 V AC / +10/-15 % / 50 Hz
Leistung: 27 W / 30 VA
Einschaltdauer: 30 % (ON: 3 Min. / OFF: 7 Min.)
Druckkraft: 1000 N (Drucklastdiagramm beachten)
+ 20 % Abschaltreserve (kurzzeitig)
Zugkraft: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Hub: 1000 mm
Laufgeschwindigkeit AUF: 10 mm/s
Laufgeschwindigkeit ZU: 10 mm/s
Schutzart: IP 65
Emissions-Schalldruckpegel: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Temperaturstandsicherheit: B300 (30 min / 300 °C)
Ausstellmechanik: Wartungsfreie Edelstahl-Zahnstange (V2A)
Tubus: Aluminium, pulverbeschichtet, weißaluminium (~ RAL 9006)
Gehäuse Motor: Polycarbonat, grau (~ RAL 7035)
Anschluss: 2,5 m Silikonkabel
Abmessungen (BxHxT):
Tubus 1162 x 30 x 30 mm
Gehäuse Motor (aufbauend auf Tubus) 160 x 104 x 46 mm
Re = 1000 Doppelhübe
Le = 20000 Doppelhübe*
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Lieferumfang:
Antriebseinheit mit 2,5 m Silikonanschlusskabel, Augenschraube (6 mm Auge), Gebrauchsanleitung
 
Fabrikat: D+H Mechatronic AG
Typ: ZA 105/1000-K
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.92	Rack and pinion drive - ZA-K - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Direct control via 230 V AC. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. The drive unit can also be changed from left to right.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 27 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1000 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 1000 N
Nominal locking force **: Max. 1400 N (1100 N ***)
Service life: > 20000 double strokes *
Stroke: 100 mm - 1500 mm
OPEN running speed: 10 mm/s
CLOSED running speed: 10 mm/s
Type of protection: IP 65
Emission sound pressure level: LpA ≤ 51 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Stainless steel rack (V2A), maintenance -free
Tube: Aluminium
Colour: on request
Housing motor: Polycarbonate
Colour: on request
Connection: Silicone cable
Dimensions (WxHxD):
Tube 225-1662 x 30 x 30 mm
Housing motor 160 x 104 x 46 mm
Re = 1000 double strokes
Le = 20000 double strokes *
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, eyebolt (6 mm eye), instruction for use
 
Brand: D+H Mechatronic AG
Type: ZA-K
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.007.00

1.1.93	Extension functions ZA-K
	Option "OT" -Reduced swivel range by omitting the tube
	Option "W" -Weatherproof for outdoor use
	Option "WS" -Swimming pool protected for use in swimming pools
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.94	ZA-BS001-OM - for Wicona® WICTEC 50/60
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICTEC 50/60;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Wicona®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A die cast close-grain stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB001-OM (27.BAB.KS)
1x Frame bracket ZA-FB002-SM (27.BAJ.KS)
1x Threaded plate 6x12x150mm (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS001-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BAF.KS

1.1.95	ZA-BS004-OM - for Gutmann® S70
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Gutmann®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A die cast close-grain stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB001-OM (27.BAB.KS)
1x Frame bracket ZA-FB002-SM (27.BAJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS004-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.96	ZA-BS006-OM - for Heroal® 180
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Heroal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB005-HE180-OM (27.BAL.KS)
1x Frame bracket ZA-FB003-OM (27.BAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS006-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.97	ZA-BS008-OM - for Jet-Brakel Aero® Ventria TG
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Jet-Brakel Aero® Ventria TG;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Jet-Brakel Aero®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB006-VentriaTG-OM (27.BAY.KS)
1x Frame bracket ZA-FB008 (27.BCT.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS008-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BAR.KS

1.1.98	ZA-BS010-OM - for Schüco® Royal S 88D
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 88D;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Frame bracket
Material: Stainless steel A2
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB009-RS88D-OM (27.BBA.KS)
1x Frame bracket ZA-FB003-OM (27.BAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS010-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.99	ZA-BS012-OM - for Schüco® Royal S 106D
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 106D;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Frame bracket
Material: Stainless steel A2
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB003-RS106D-OM (27.BAW.KS)
1x Frame bracket ZA-FB003-OM (27.BAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS012-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.100	ZA-BS014-OM - for Hueck® 85E
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB012-HU85E-OM (27.BBJ.KS)
1x Frame bracket ZA-FB005 (27.BBM.KS)
1x Threaded plate 6x12x150 mm (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS014-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.101	ZA-BS016-OM - for Sapa® 5050 + 5060
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 5050 + 5060;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Sapa®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Set contents:
1x Sash bracket ZB-SB014-OM (27.BBL.KS)
1x Frame bracket ZA-FB003-OM (27.BAN.KS)
1x Adapter angle ZA (68.102.73)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS016-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BBP.KS

1.1.102	ZA-BS018-OM - for Hueck® 1.0 (window frame 519510)
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0 (window frame 519510);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB014-OM (27.BBL.KS)
1x Frame bracket ZA-FB003-OM (27.BAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS018-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.103	ZA-BS019-OM - for Hueck® 1.0 (window frame 519511)
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0 (window frame 519511) ;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Basic bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZB-SB014-OM (27.BBL.KS)
1x Basic bracket ZA-BB002-OM (27.BBU.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS019-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.104	ZA-BS021-OM - for Reynaers® CR 120
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CR 120;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB016-CR120-OM (27.BBX.KS)
1x Frame bracket ZA-FB003-OM (27.BAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS021-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.105	ZA-BS023-OM - for Colt® Kameleon E
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Colt®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB018-CEKE-OM (27.BCD.KS
1x Frame bracket ZA-FB003-OM (27.BAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS023-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.106	ZA-BS028-OM - for Schüco® AWS 57 (369 770 + 369 780)
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (369 770 + 369 780);
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB019-AWS57RO-OM (27.BCJ.KS)
1x Frame bracket ZA-FB005 (27.BBM.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS028-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BCM.KS

1.1.107	ZA-BS030-OM - for Schüco® AWS 57 (331 810 + 331 820)
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (331 810 + 331 820);
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB019-AWS57RO-OM (27.BCJ.KS)
1x Frame bracket ZA-FB007 (27.BCL.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS030-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BCR.KS

1.1.108	ZA-BS034-OM - for Aluprof® MB-SR50
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-SR50;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Aluprof®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB012-HU85E-OM (27.BBJ.KS)
1x Frame bracket ZA-FB005 (27.BBM.KS)
Including all necessary fastening materialsl
 
Brand: D+H Mechatronic AG
Type: ZA-BS034-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.109	ZA-BS036-OM - for Technal® MX
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Technal® MX;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Technal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB014-OM (27.BBL.KS)
1x Frame bracket ZA-FB007 (27.BCL.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS036-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.110	ZA-BS037-OM - for Reynaers® Flush Roof Vent
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB014-OM (27.BBL.KS)
1x Frame bracket ZA-FB002-SM (27.BAJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS037-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDE.KS

1.1.111	ZA-BS040-OM - for Heroal® 180ES
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180ES;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Heroal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB012-HU85E-OM (27.BBJ.KS)
1x Frame bracket ZA-FB007-OM (27.BCL.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS040-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDH.KS

1.1.112	ZA-BS042-OM - for Raico® WING 105DI
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A die cast close-grain stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS042-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDA.KS

1.1.113	ZA-BS044-OM - for Aluprof® MB-RW
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Aluprof®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A die cast close-grain stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB001-OM (27.BAB.KS)
1x Frame bracket ZA-FB009-OM (27.BDM.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS044-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDK.KS

1.1.114	ZA-BS049-OM - for Raico® FRAME+ 100/120RI
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A die cast close-grain stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS049-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDT.KS

1.1.115	ZA-BS051-OM - for Raico® FRAME+ 100RI-T
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A die cast close-grain stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS051-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDV.KS

1.1.116	ZA-BS053-OM - for Raico® FRAME+ 120RI-T
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 120RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A die cast close-grain stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS053-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDX.KS

1.1.117	ZA-BS002-SM - for Wicona® WICTEC 50/60
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICTEC 50/60;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Wicona®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB002-SM (27.BAD.KS)
1x Frame bracket ZA-FB002-SM (27.BAJ.KS)
1x Threaded plate 6x12x150mm (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS002-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BAE.KS

1.1.118	ZA-BS003-SM - for Gutmann® S70
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Gutmann®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB002-SM (27.BAD.KS)
1x Frame bracket ZA-FB002-SM (27.BAJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS003-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.119	ZA-BS005-SM - for Heroal® 180
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Heroal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB007-HE180-SM (27.BAU.KS)
1x Frame bracket ZA-FB004-SM (27.BAS.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS005-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.120	ZA-BS007-SM - for Jet-Brakel Aero® Ventria TG
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Jet-Brakel Aero® Ventria TG;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Jet-Brakel Aero®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB008-VentriaTG-SM (27.BAZ.KS)
1x Frame bracket ZA-FB008 (27.BCT.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS007-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.121	ZA-BS009-SM - for Schüco® Royal S 88D
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 88D;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Basic bracket
Material: Stainless steel A2,
Surface: Tumbled
 
Adapter bracket
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB010-RS88D-SM (27.BBB.KS)
1x Basic bracket ZA-BB001-SM (27.BAC.KS)
1x Adapter bracket AB001-RS88D-SM (27.CMA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS009-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.122	ZA-BS011-SM - for Schüco® Royal S 106D
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 106D;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Frame bracket
Material: Aluminium / stainless steel A2
Surface: Anodized E6 EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB004-RS106D-SM (27.BAX.KS)
1x Frame bracket ZA-FB004-SM (27.BAS.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS011-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.123	ZA-BS013-SM - for Hueck® 85E
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB011-HU85E-SM (27.BBH.KS)
1x Frame bracket ZA-FB005 (27.BBM.KS)
1x Threaded plate 6x12x150 mm (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS013-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.124	ZA-BS015-SM - for Sapa® 5050 + 5060
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 5050 + 5060;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Sapa®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Adapterwinkel
Material V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZB-SB013-SM (27.BBK.KS)
1x Frame bracket ZA-FB004-SM (27.BAS.KS)
1x Adapter angle ZA (68.102.73)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS015-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.125	ZA-BS017-SM - for Hueck® 1.0 (window frame 519510)
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0 (window frame 519510);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB03-SM (27.BBK.KS)
1x Frame bracket ZA-FB006 (27.BBT.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS017-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.126	ZA-BS020-SM - for Reynaers® CR 120
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CR 120;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems ofn Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB015-CR120-SM (27.BBW.KS)
1x Frame bracket ZA-FB004-SM (27.BAS.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS020-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.127	ZA-BS022-SM - for Colt® Kameleon E
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Colt®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB017-CEKE-SM (27.BCC.KS)
1x Frame bracket ZA-FB004-SM (27.BAS.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS022-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.128	ZA-BS029-SM - for Schüco® AWS 57 (369 770 + 369 780)
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (369 770 + 369 780);
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB020-AWS57RO-SM (27.BCK.KS)
1x Frame bracket ZA-FB005 (27.BBM.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS029-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BCN.KS

1.1.129	ZA-BS031-SM - for Schüco® AWS 57 (331 810 + 331 820)
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (331 810 + 331 820);
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB020-AWS57RO-SM (27.BCK.KS)
1x Frame bracket ZA-FB007 (27.BCL.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS031-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BCP.KS

1.1.130	ZA-BS033-SM - for Aluprof® MB-SR50
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-SR50;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Aluprof®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB021-SM (27.BCU.KS)
1x Frame bracket ZA-FB002-SM (27.BAJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS033-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BCV.KS

1.1.131	ZA-BS035-SM - for Technal® MX
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Technal® MX;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Technal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB021-SM (27.BCU.KS)
1x Frame bracket ZA-FB007 (27.BCL.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS035-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.132	ZA-BS038-SM - for Reynaers® Flush Roof Vent
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB021-SM (27.BCU.KS)
1x Frame bracket ZA-FB002 (27.BAJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS038-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDF.KS

1.1.133	ZA-BS041-SM - for Heroal® 180ES
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180ES;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Heroal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB002-SM (27.BAD.KS)
1x Frame bracket ZA-FB002-SM (27.BAJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS041-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.134	ZA-BS043-SM - for Raico® WING 105DI
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS043-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BCZ.KS

1.1.135	ZA-BS045-SM - for Aluprof® MB-RW
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Aluprof®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket ZA-SB002-SM (27.BAD.KS)
1x Frame bracket ZA-FB010-SM (27.BDN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS045-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDL.KS

1.1.136	ZA-BS048-SM - for Raico® FRAME+ 100/120RI
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS048-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDS.KS

1.1.137	ZA-BS050-SM - for Raico® FRAME+ 100RI-T
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS050-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDU.KS

1.1.138	ZA-BS052-SM - for Raico® FRAME+ 120RI-T
ZA bracket set, for side installation
 
Performance features:
For mounted installation of ZA drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 120RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A die cast close-grain stainless steel / V2A stainless steel
Surface: Sandblasted / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: ZA-BS052-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.BDW.KS

1.1.139	ZA-BS027-OM - for Reynaers® CS 59, CS 68, CS 77, CS 86-HI, Eco
ZA bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of bottom-hung and top-hung windows (façade windows);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CS 59, CS 68, CS 77, CS 86-HI, Eco;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket FK-D (20.052.20)
1x Frame bracket ZA-FB005 (27.BBM.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: ZA-BS027-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.140	Sash bracket - FK
for ZA drives
 
Performance features:
With releasable bolt;
 
Technical data:
Material: Die-cast zinc
 
Brand: D+H Mechatronic AG
Type: FK
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.050.80

1.1.141	Sash bracket - FK-D
for ZA drives
 
Performance features:
With releasable bolt;
 
Technical data:
Material: Aluminium
Surface: Anodized E6 / EV1
 
Brand: D+H Mechatronic AG
Type: FK-D
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.052.20

1.1.142	Cover sheet - AD-FK
for ZA sash bracket FK-D
 
Performance features:
To cover the original handle hole;
 
Technical data:
Material: Aluminium
Surface: Anodized E6 / EV1
 
Brand: D+H Mechatronic AG
Type: AD-FK
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 68.100.03

1.1.143	Sash bracket - FKE
for ZA drives
 
Performance features:
Can be unlocked;
With spring-loaded release pin, e.g. for roof access trapdoor;
 
Technical data:
Material: Die-cast zinc
 
Brand: D+H Mechatronic AG
Type: FKE
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.052.30

1.1.144	Sash bracket - FKK
for ZA drives
 
Performance features:
With releasable bolt;
 
Technical data:
Material: V2A stainless steel
 
Brand: D+H Mechatronic AG
Type: FKK
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.052.40

1.1.145	Ball angle joint - KWG
for ZA drives
 
Performance features:
As eyebolt replacement;
 
Technical data:
Pull-out strength: approx. 1500 N
Material: Aluminium / steel
Surface: Anodized E6 / EV1
 
Brand: D+H Mechatronic AG
Type: KWG
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.051.40

1.1.146	Angle bracket - WK 6
for ZA drives
 
Performance features:
With 2 stud bolts and locknuts;
 
Technical data:
Material: Die-cast aluminium
 
Brand: D+H Mechatronic AG
Type: WK 6
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.052.60

1.1.147	Angle bracket - ZK 6
for ZA drives
 
Performance features:
With 2 stud bolts and locknuts;
 
Technical data:
Material: Die-cast aluminium
 
Brand: D+H Mechatronic AG
Type: ZK 6
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.052.70

1.1.148	Z-bracket - ZKK
for ZA drives
 
Performance features:
Adjustable bracket with 2 stud bolts and locknuts;
 
Technical data:
Material: V2A stainless steel
 
Brand: D+H Mechatronic AG
Type: ZKK
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.052.80

1.1.149	U-bracket - UK 50
for ZA drives
 
Performance features:
Bracket with through bolt;
 
Technical data:
Material: Aluminium
Surface: Anodized E6 / EV1
 
Brand: D+H Mechatronic AG
Type: UK 50
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.050.00

1.1.150	U-bracket - UK 350
for ZA drives
 
Performance features:
Bracket with 2 stud bolts and locknuts;
 
Technical data:
Material: Aluminium
Surface: Anodized E6 / EV1
Length: 350 mm
 
Brand: D+H Mechatronic AG
Type: UK 350
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.050.10

1.1.151	U-bracket - UK 500
for ZA drives
 
Performance features:
Bracket with 2 stud bolts and locknuts;
 
Technical data:
Material: Aluminium
Surface: Anodized E6 / EV1
Length: 500 mm
 
Brand: D+H Mechatronic AG
Type: UK 500
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.050.20

1.1.152	Pivot point displacemant bracket - DPK 6
for ZA drives
 
Performance features:
Bracket with terminal part, 2 stud bolts and locknuts;
 
Technical data:
Material: Aluminium
Surface: Anodized E6 / EV1
 
Brand: D+H Mechatronic AG
Type: DPK 6
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.052.00

1.1.153	Pivot point displacemant bracket - DPK 8
for ZA drives
 
Performance features:
Pivoting bracket with mounting plate, terminal part, 2 stud bolts and locknuts;
 
Technical data:
Material: Aluminium
Surface: Anodized E6 / EV1
 
Brand: D+H Mechatronic AG
Type: DPK 8
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.051.50

1.1.154	Side bracket - SK
for ZA drives
 
Performance features:
Bracket for diagonal installation of drive on window sashes;
 
Technical data:
Material: V2A stainless steel
Surface: Trowalisiert
 
Brand: D+H Mechatronic AG
Type: SK
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.050.40

1.1.155	Side bracket - SK-D
for ZA drives
 
Performance features:
Pivoting bracket for diagonal installation of drive on window sashes;
Consisting of DPK terminal part installed on SK triangular bracket;
 
Technical data:
Material: V2A stainless steel
Surface: Trowalisiert
 
Brand: D+H Mechatronic AG
Type: SK-D
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.050.60

Information Selection Guide

Technologie BSY+
BSY+ enables communication and synchronisation between different components in the window. For example between the chain drives, during synchronous operation, or between window and locking drives (e.g. FRA 11 BSY+ or VLD-BSY+). 
1.1.156	BSY+ High-performance rack and pinion drive - DXD 300/1000-BSY+OT-HS
24 V DC / 5 A / 2000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of extremely heavy windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Synchronisation of up to 4 drives High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Drive functions and different drive parameters are pre-installed at the factory (according to customer specification) or individually programmable on site via the D+H software SCS. A groove in the drive tube allows flexible installation. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
2000 N continuous load
3000 N short time load
Tensile force: 2000 N
Nominal locking force **: 2800 N
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - HS: 17 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 64
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: DXD 300/1000-BSY+ OT-HS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.027.20

1.1.157	BSY+ High-performance rack and pinion drive - DXD 300-BSY+ - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of extremely heavy windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Synchronisation of up to 4 drives. High-speed function (HS) for especially fast opening windows in case of fire (SHEV) (optional). Drive functions and different drive parameters are pre-installed at the factory (according to customer specification) or individually programmable on site via the D+H software SCS. A groove in the drive tube allows flexible installation. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2.5 A (5 A with HS)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
2000 N continuous load
3000 N short time load
Tensile force: 1000 N
Nominal locking force **: 2800 N
Service life: > 20000 double strokes *
Stroke: 500 mm - 1500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
OPEN running speed - HS: 17 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 64
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Tube: Aluminium
Colour: on request
Housing motor: Polycarbonate
Colour: on request
Connection: Silicone cable
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: DXD 300-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.022.06

1.1.158	Extension functions DXD 300-BSY+
	Option "HS" -High-Speed option for SHEV application possible
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "BRV" -Signal for connection to FRA, VLD, ERM 44 or AT 41
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "W" -Weatherproof for outdoor use
	Option "WS" -Swimming pool protected for use in swimming pools
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.159	BSY+ High-performance rack and pinion drive - DXD 300/1000-K-BSY+ OT HS
230 V AC / 175 VA / 2000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of extremely heavy windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Synchronisation of up to 4 drives High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Drive functions and different drive parameters are pre-installed at the factory (according to customer specification) or individually programmable on site via the D+H software SCS. A groove in the drive tube allows flexible installation. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above.
 
Technical data:
Operating voltage: 230 V AC / ±10 %
Performance: 140 W / 175 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
2000 N continuous load
3000 N short time load
Tensile force: 2000 N
Nominal locking force **: 2800 N
Service life: > 20000 double strokes *
Stroke: 1000 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - HS: 17 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 64
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Tube: Aluminium, powder-coated, white aluminium (~ RAL 9006)
Housing motor: Polycarbonate, grey (~ RAL 7035)
Connection: 2.5 m silicone cable
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: DXD 300/1000-K-BSY+ OT HS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.027.20

1.1.160	BSY+ High-performance rack and pinion drive - DXD 300-K-BSY+ - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of extremely heavy windows, flaps and skylights. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Synchronisation of up to 4 drives High-speed function (HS) for especially fast opening windows in case of fire (SHEV) (optional). Drive functions and different drive parameters are pre-installed at the factory (according to customer specification) or individually programmable on site via the D+H software SCS. A groove in the drive tube allows flexible installation. Particularly quiet daily ventilation mode. Electronic limit stop and overload cut-off protect the element and the drive from damage. The power supply can be connected either from below or above. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / ±10 %
Performance: 70 W / 95 VA (140 W / 175 VA with HS)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
2000 N continuous load
3000 N short time load
Tensile force: 2000 N
Nominal locking force **: 2800 N
Service life: > 20000 double strokes *
Stroke: 500 mm - 1500 mm
OPEN running speed: 7.1 mm/s
OPEN running speed - SHEV: 8 mm/s
OPEN running speed - HS: 17 mm/s
CLOSED running speed: 7.1 mm/s
Type of protection: IP 64
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range: -15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Tube: Aluminium
Colour: on request
Housing motor: Polycarbonate
Colour: on request
Connection: Silicone cable
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: DXD 300-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 20.022.08

1.1.161	Extension functions DXD 300-K-BSY+
	Option "HS" -High-Speed option for SHEV application possible
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "W" -Weatherproof for outdoor use
	Option "WS" -Swimming pool protected for use in swimming pools
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.162	DXD-BS003-OM - for Wicona® WICTEC 50/60
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICTEC 50/60;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems ofWicona®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB023-OM (27.ABE.KS)
1x Frame bracket DXD-FB001-OM (27.ABT.KS)
1x Adapter angle OM (65.401.92)
1x Support 37 mm (27.AZZ.KS)
1x Threaded plate (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS003-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.AAK.KS

1.1.163	DXD-BS005-OM - for Schüco® Royal S 106D
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 106D;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Basic bracket
Material: Stainless steel A2
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB001-RS106D-OM (27.AAD.KS)
1x Basic bracket DXD-BB001-OM (27.AAA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS005-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.164	DXD-BS007-OM - for Schüco® Royal S 88D
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 88D;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Basic bracket
Material: Stainless steel A2
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB005-RS88D-OM (27.AAN.KS)
1x Basic bracket DXD-BB001-OM (27.AAA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS007-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.165	DXD-BS009-OM - for Heroal® 180
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Heroal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Basic bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB013-HE180D-OM (27.AAU.KS)
1x Basic bracket DXD-BB001-OM (27.AAA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS009-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.166	DXD-BS011-OM - for Gutmann® S70
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Gutmann®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB023-OM (27.ABE.KS)
1x Frame bracket DXD-FB002-OM (27.ABY.KS)
1x Adapter angle OM (65.402.32)
1x Support 25 mm (27.AZU.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS011-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.167	DXD-BS013-OM - for Hueck® 85E
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB027HU85E-OM (27.ABJ.KS)
1x Frame bracket DXD-FB002-OM (27.ABY.KS)
1x Support 62 mm (27.AZV.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS013-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.168	DXD-BS015-OM - for Hueck® 1.0 (window frame 519510)
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0 (window frame 519510);
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Basic bracket
Material: Stainless steel A2
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB019HU1.0-OM (27.ABA.KS)
1x Basic bracket DXD-BB001-OM (27.AAA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS015-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.169	DXD-BS017-OM - for Hueck® 1.0 (window frame 519511)
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0 (window frame 519511);
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB019-HU1.0-OM (27.ABA.KS)
1x Frame bracket DXD-FB005-OM (27.ABX.KS)
1x Support 62 mm (27.AZV.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS017-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.170	DXD-BS019-OM - for Sapa® SFB 5050 + 5060
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 5050 + 5060;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Sapa®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB031-SASFB-OM (27.ABN.KS)
1x Frame bracket DXD-FB005-OM (27.ABX.KS)
1x Adapter DXD (65.402.30)
1x Support 62 mm (27.AZV.KS)
1x Threaded plate (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS019-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.ACD.KS

1.1.171	DXD-BS021-OM - for Jet-Brakel Aero® Ventira TG
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Jet-Brakel Aero® Ventira TG;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Jet-Brakel Aero®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Basic bracket with adapter plate
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB015-OM (27.AAW.KS)
1x Basic bracket DXD-BB001-OM (27.AAA.KS)
1x Adapter plate Ventria TG-OM (65.402.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS021-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.ACF.KS

1.1.172	DXD-BS023-OM - for Reynaers® CR 120
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CR 120;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Basic bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB034-CR120-OM (27.ACK.KS)
1x Basic bracket DXD-BB001-OM (27.AAA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS023-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.173	DXD-BS025-OM - for Colt® Kameleon E
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Basic bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB036-CEKE-OM (27.ACT.KS)
1x Basic bracket DXD-BB001-OM (27.AAA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS025-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.174	DXD-BS028-OM - for Schüco® AWS 57 RO + Aluprof® MB SR 50
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Schüco® AWS 57 RO, Aluprof® MB SR 50;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco® and Aluprof®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB015-OM (27.AAW.KS)
1x Frame bracket DXD-FB010-OM (27.ACY.KS)
1x Adapter angle OM (65.402.32)
1x Support 37 mm (27.AZZ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS028-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.ACW.KS

1.1.175	DXD-BS031-OM - for Reynaers® Flush Roof Vent
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB015-OM (27.AAW.KS)
1x Frame bracket DXD-FB002-OM (27.ABY.KS)
1x Adapter angle OM (65.402.32)
1x Support 37 mm (27.AZZ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS031-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.176	DXD-BS036-OM - for Raico® WING 105DI (208 310)
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI (208 310);
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS036-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.177	DXD-BS037-OM - for Raico® WING 105DI (208 312)
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI (208 312);
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS037-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.ADE.KS

1.1.178	DXD-BS038-OM - for Aluprof® MB-RW
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB023-OM (27.ABE.KS)
1x Frame bracket DXD-FB012-OM (27.ADU.KS)
1x Adapter angle OM (65.402.32)
1x Support 25 mm (27.AZU.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS038-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.179	DXD-BS041-OM - for Raico® FRAME+ 100/120RI
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Support 37 mm
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS041-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.ADX.KS

1.1.180	DXD-BS043-OM - for Raico® FRAME+ 100RI-T
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100RI-T;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Support 37 mm
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS043-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.181	DXD-BS045-OM - for Raico® FRAME+ 120RI-T
DXD bracket set, for installation opposite the hinge
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 120RI-T;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Support 37 mm
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS045-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.182	DXD-BS001-SM - for Wicona® WICTEC 50/60
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICTEC 50/60;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Wicona®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB021-SM (27.ABC.KS)
1x Frame bracket DXD-FB003-SM (27.ABR.KS)
1x Adapter angle SM (65.401.90)
1x Support 75 mm (27.AZX.KS)
1x Threaded plate (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS001-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.183	DXD-BS006-SM - for Schüco® Royal S 106D
DXD bracket set, for side installation
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 106D;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Basic bracket
Material: Stainless steel A2
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB003-RS106D-SM (27.AAF.KS)
1x Basic bracket DXD-BB003-SM (27.AAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS006-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.184	DXD-BS008-SM - for Schüco® Royal S 88D
DXD bracket set, for side installation
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 88D;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Basic bracket
Material: Stainless steel A2
Surface:Tumbled
 
Adapter bracket
Material: Aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB007-RS88D-SM (27.AAL.KS)
1x Basic bracket DXD-BB003-SM (27.AAE.KS)
1x Adapter bracket AB001-RS88D-SM (27.CMA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS008-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.185	DXD-BS010-SM - for Heroal® 180
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Heroal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Basic bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB011-HE180D-SM (27.AAM.KS)
1x Basic bracket DXD-BB003-SM (27.AAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS010-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.186	DXD-BS012-SM - for Gutmann® S70
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Gutmann®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB021-SM (27.ABC.KS)
1x Frame bracket DXD-FB003-SM (27.ABR.KS)
1x Adapter angle SM (65.401.90)
1x Support 62 mm (27.AZV.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS012-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.187	DXD-BS014-SM - for Hueck® 85E
DXD bracket set, for side installation
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB025HU85E-SM (27.ABG.KS)
1x Frame bracket DXD-FB008-SM (27.ACH.KS)
1x Support 87 mm (27.AZW.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS014-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.188	DXD-BS016-SM - for Hueck® 1.0 (window frame 519510)
DXD bracket set, for side installation
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0 (window frame 519510);
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB017-HU1.0-SM (27.AAY.KS)
1x Frame bracket DXD-FB006-SM (27.ABZ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS016-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.189	DXD-BS018-SM - for Hueck® 1.0 (window frame 519511)
DXD bracket set, for side installation
 
Performance features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0 (window frame 519511);
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB017-HU1.0-SM (27.AAY.KS)
1x Frame bracket DXD-FB004-SM (27.ABW.KS)
1x Support 62 mm (27.AZV.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS018-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.190	DXD-BS020-SM - for Sapa® SFB 5050 + 5060
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 5050 + 5060;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Sapa®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter + support
Material: Aluminium /V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB029-SASFB-SM (27.ABL.KS)
1x Frame bracket DXD-FB004-SM (27.ABW.KS)
1x Adapter DXD (65.402.30)
1x Support 62 mm (27.AZV.KS)
1x Threaded plate (65.401.93)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS020-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.191	DXD-BS022-SM - for Jet-Brakel Aero® Ventira TG
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Jet-Brakel Aero® Ventira TG;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Jet-Brakel Aero®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter plate
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB009-Ventria TG-SM (27.AAT.KS)
1x Frame bracket DXD-FB007-Ventria TG-SM (27.ABV.KS)
1x Adapter plate Ventria TG (65.401.83) and strike plate (65.401.80)
Including all necessary fastening materialsl
 
Brand: D+H Mechatronic AG
Type: DXD-BS022-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.192	DXD-BS024-SM - for Reynaers® CR 120
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CR 120;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter plate
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB033-CR120-SM (27.ACJ.KS)
1x Frame bracket DXD-FB009-CR120-SM (27.ACN.KS)
1x Adapter plate CR120-SM (65.402.95)
Including all necessary fastening materialsl
 
Brand: D+H Mechatronic AG
Type DXD-BS024-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.193	DXD-BS026-SM - for Colt® Kameleon E
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB035-CEKE-SM (27.ACS.KS)
1x Frame bracket DXD-FB006-SM (27.ABZ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS026-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.194	DXD-BS029-SM - for Schüco® AWS 57 RO
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 RO;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB037-AWS57RO-SM (27.ACV.KS)
1x Frame bracket DXD-FB003-SM (27.ABR.KS)
1x Adapter angle SM (65.401.90)
1x Support 75 mm (27.AZX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS029-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.ACX.KS

1.1.195	DXD-BS030-SM - for Aluprof® MB-SR50
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-SR50;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Aluprof®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB038-SM (27.ACZ.KS)
1x Frame bracket DXD-FB008-SM (27.ACH.KS)
1x Adapter angle SM (65.402.81)
1x Support 62 mm (27.AZV.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS030-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.196	DXD-BS032-SM - for Reynaers® Flush Roof Vent
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Reynaers®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB038-SM (27.ACZ.KS)
1x Frame bracket DXD-FB011-SM (27.ADP.KS)
1x Adapter angle SM (65.402.81)
1x Support 75 mm (27.AZX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS032-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.197	DXD-BS033-SM - for Heroal® 180ES
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180ES;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Heroal®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB025-HU85E-SM (27.ABG.KS)
1x Frame bracket DXD-FB008-SM (27.ACH.KS)
1x Adapter angle SM (65.402.81)
1x Support 62 mm (27.AZV.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS033-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.198	DXD-BS034-SM - for Raico® WING 105DI (208 310)
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI (208 310);
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS034-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.199	DXD-BS035-SM - for Raico® WING 105DI (208 312)
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI (208 312);
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS035-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.200	DXD-BS039-SM - for Aluprof® MB-RW
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
Bracket designed for max. force of 3000 N.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket with adapter angle + support
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Scope of supply:
Set contents:
1x Sash bracket DXD-SB021-SM (27.ABC.KS)
1x Frame bracket DXD-FB013-SM (27.ADV.KS)
1x Adapter angle SM (65.402.81)
1x Support 75 mm (27.AZX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: DXD-BS039-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.201	DXD-BS040-SM - for Raico® FRAME+ 100/120RI
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Support 75 mm
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS040-SM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 27.ADW.KS

1.1.202	DXD-BS042-SM - for Raico® FRAME+ 100RI-T
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100RI-T;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Support 75 mm
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS042-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.203	DXD-BS044-SM - for Raico® FRAME+ 100RI-T
DXD bracket set, for side installation
 
Performace features:
For mounted installation of DXD drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 120RI-T;
Bracket designed for max. force of 3000 N.
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / tumbled
 
Support 75 mm
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: DXD-BS044-SM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk