1	D+H Mechatronic (english)
1.1	Chain drives
Information on power-operated windows

When manufacturing and operating power-operated opening elements, the applicable safety regulations must be observed. A risk assessment in accordance with the Machinery Directive 2006/42/EEC must be carried out by the manufacturer with the introduction of the product standard DIN EN 1453-1 and documented on the power-operated window by means of an EC Declaration of Conformity and the CE marking.
Information on bracket technology

For special solutions and CAD sections of the brackets, please contact your local project consultant.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)
Information Selection Guide

Technologie LIGHT (K)
LIGHT actuators (230 V AC) can only be controlled in OPEN and CLOSE direction.
 
 
Technologie TMS+
Up to two drives can be connected together. The output of the BRV signal only occurs in the end positions - therefore no malfunction with locking drives or modules. During the teaching phase, the adjusted stroke is transmitted to the tandem drive via the TMS+ function.
 
 
Technologie PLP
Data transmission via the drive‘s connection cable. Drive characteristics can be programmed directly via the supply cable. Thus, no additional cable is required for parameterisation.
 
 
Technologie ACB
Enables direct bus communication between the controller and the drive for, for example, control with perfect positioning or drive feedback. Communication is via the open source Modbus protocol, and it enables the drive to be combined with an ACB?capable control panel or enables it to be directly connected to higher-level controllers such as a building management system.
1.1.1	PLP chain drive - VCD 203/250 (SR)
24 V DC / 0.35 A / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N / 4000 N ***
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 300 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** Optionally increased nominal locking force
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 203/250 (SR)
 
https://www.dh-partner.com/en/service/planning-support.html

Unit : Stk
Artikelnr. : 25.150.05

1.1.2	PLP chain drive - VCD 203/250 (BK)
24 V DC / 0.35 A / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N / 4000 N ***
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 300 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** Optionally increased nominal locking force
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 203/250 (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.150.07

1.1.3	PLP chain drive - VCD 203/250 (WH)
24 V DC / 0.35 A / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N / 4000 N ***
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 300 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** Optionally increased nominal locking force
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 203/250 (WH)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.150.06

1.1.4	PLP chain drive - VCD 203-PLP - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N / 4000 N ***
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: on request
Colour: on request
Connection: PVC-cable
Dimensions (WxHxD): 300 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** Optionally increased nominal locking force
 
Scope of supply:
Drive unit with PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 203-PLP
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.150.00

1.1.5	Extension functions VCD 0203-PLP
	Option "CP" - Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" - Stroke programming
	Option "SA" - End position message "switch OPEN"
	Option "SZ" - End position message "switch CLOSED"
	Option "special colour" - Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.6	PLP chain drive - VCD 204/250 (SR)
24 V DC / 0.35 A / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250 (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.100.05

1.1.7	PLP chain drive - VCD 204/250 (BK)
230 V AC / 15 VA / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250-K (BK)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.8	PLP chain drive - VCD 204/250 (WH)
24 V DC / 0.35 A / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250 (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.9	PLP chain drive - VCD 204/350 (SR)
24 V DC / 0.35 A / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350 (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.100.10

1.1.10	PLP chain drive - VCD 204/350-DS (SR)
24 V DC / 0.35 A / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit (with loop option) for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-DS (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.100.10

1.1.11	PLP chain drive - VCD 204/350 (BK)
24 V DC / 0.35 A / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350 (BK)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.12	PLP chain drive - VCD 204/350 (WH)
24 V DC / 0.35 A / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350 (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.13	PLP chain drive set - VCD 204/350-TMS+ Set (SR)
24 V DC / 2x 0.35 A / 2x 200 N / 350 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
(per drive)
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking forceNominal locking force **Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units (one drive equipped with DS-Option) with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-TMS+ Set (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.122.05

1.1.14	PLP chain drive set - VCD 204/350-TMS+ Set (BK)
24 V DC / 2x 0.35 A / 2x 200 N / 350 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
(per drive)
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units (one drive equipped with DS-Option) with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-TMS+ Set (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.122.07

1.1.15	PLP chain drive set - VCD 204/350-TMS+ Set (WH)
24 V DC / 2x 0.35 A / 2x 200 N / 350 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
(per drive)
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units (one drive equipped with DS-Option) with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-TMS+ Set (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.16	PLP chain drive - VCD 204-PLP - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation.
The drive is equipped with motor electronics controlled via microprocessor. Programmable drive functions and performance features via Powerline (PLP) and the D+H software SCS. The drive is equipped with a special chain stabilisation and centred chain outlet. "TMS+" tandem safety function for operating 2 drives on one sash is standard. Alternatively the drive can also be operated with a locking drive. In case of a tandem version learning with magnet will be transmitted to dual drive; Option of chain stroke programming via magnet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector.
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm / 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: on request
Colour: on request
Connection: PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204-PLP
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.100.00

1.1.17	Extension functions VCD 204-PLP
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "DS" -Loop-through option enables connection with one additional D+H drive
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.18	ACB chain drive - VCD-0203-0250-1-ACB M1-R
24 V DC / 0.35 A / 200 N / 250 mm stroke
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
High-precise motor- and synchron electronic for parallel run for up to 8 drives;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication (incl. locking drive)/ group signal
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N / 4000 N ***
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 300 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** Optionally increased nominal locking force
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0203-0250-1-ACB M
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.05

1.1.19	ACB chain drive - VCD-0203-1-ACB - freely configurable
24 V DC / Special production according to customer requirements
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
High-precise motor- and synchron electronic for parallel run for up to 8 drives;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication (incl. locking drive)/ group signal
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Design: Right
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N / 4000 N ***
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Surface: on request
Colour: on request
Connection: PVC-cable
Dimensions (WxHxD): 300 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** Optionally increased nominal locking force
 
Scope of supply:
Drive unit with PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0203-1-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.10

1.1.20	Extension functions VCD-0203-xxxx-1-ACB
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "X" - Increased nominal locking force max. 4000 N
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.21	ACB chain drive - VCD-0204-0250-1-ACB M1-M
24 V DC / 0.35 A / 200 N / 250 mm stroke
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. Symmetrical construction with centered chain outlet. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
High-precise motor- and synchron electronic for parallel run for up to 8 drives;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication (incl. locking drive)/ group signal
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Symmetric
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0204-0250-1-ACB M1-M
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.15

1.1.22	ACB chain drive - VCD-0204-0350-1-ACB M1-M
24 V DC / 0.35 A / 200 N / 350 mm stroke
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. Symmetrical construction with centered chain outlet. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
High-precise motor- and synchron electronic for parallel run for up to 8 drives;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication (incl. locking drive)/ group signal
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Symmetric
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0204-0350-1-ACB M1-M
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.25

1.1.23	ACB chain drive - VCD-0204-1-ACB - freely configurable
24 V DC / Special production according to customer requirements
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. Symmetrical construction with centered chain outlet. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
High-precise motor- and synchron electronic for parallel run for up to 8 drives;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication (incl. locking drive)/ group signal
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Design: Symmetric
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm / 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Surface: on request
Colour: on request
Connection: PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0204-1-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.35

1.1.24	Extension functions VCD-0204-xxxx-1-ACB
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "DS" -Loop-through option enables connection with D+H locking drives and open bus communication via ACB
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS2" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.25	ACB chain drive - VCD-0204-0250-5-ACB M1-M
230 V AC / 30 VA / 200 N / 250 mm stroke
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. Symmetrical construction with centered chain outlet. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
With BSY+ motor and synchronised electronics controlled via microprocessor;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 230 V AC / + 10 %/-15 %
Performance: 22 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Symmetric
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0204-0250-5-ACB M1-M
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.20

1.1.26	ACB chain drive - VCD-0204-0350-5-ACB M1-M
230 V AC / 30 VA / 200 N / 350 mm stroke
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. Symmetrical construction with centered chain outlet. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
With BSY+ motor and synchronised electronics controlled via microprocessor;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 230 V AC / + 10 %/-15 %
Performance: 22 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Symmetric
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0204-0350-5-ACB M1-M
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.30

1.1.27	ACB chain drive - VCD-0204-5-ACB - freely configurable
230 V AC / Special production according to customer requirements
 
Electromotive drive unit with Modbus RTU interface for surfaced mounting at the window profile. Symmetrical construction with centered chain outlet. For the comfortable electromotive opening and closing of bottom hung-, top hung-, parallel opening-, and trapezoidal windows in the facade, as well as for roof windows. Useable for daily ventilation mode. Compatible to D+H locking drives.
 
Performance features:
Integrated Advanced Communication Bus (ACB) with open Modbus RTU protocol;
With BSY+ motor and synchronised electronics controlled via microprocessor;
Connection of up to 4 locking drives;
Corrosion protected, hardened, rigid backing steel chain, maintenance free by lifetime lubrication;
Special chain stabilization;
Active and passive locking edge protection;
Various adjustable drive parameters (stroke, force, speed);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to polarity reversal protection connector system;
Individual parameterizing via D+H software SCS;
Low operation noises;
 
Functional description ACB
Direct integration of drive by open Modbus RTU bus-communication via Advanced Communication Bus (ACB) for the building automation, e.g. in BMS (building management system) with following features:
- Exact position operating (relative values, in 1% steps)
- Creation of virtual groups at one output
- OPEN and CLOSED-indication
- Monitoring of connected drives
- Status monitoring of motor
- Diagnostic and parameterizing directly via controller
- Modbus protocol "ACB planning manual" as download link on D+H´s website
- Max. 32 ACB-bus-participants at Modbus RTU
 
Technical data:
Operating voltage: 230 V AC / + 10 %/-15 %
Performance: 22 W / 30 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Design: Symmetric
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm / 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: two-part, die-cast zinc
Surface: on request
Colour: on request
Connection: PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD-0204-5-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.155.40

1.1.28	Extension functions VCD-0204-xxxx-5-ACB
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.29	Chain drive - VCD 204/250-K (SR)
230 V AC / 15 VA / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250-K (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.120.05

1.1.30	Chain drive - VCD 204/250-K (BK)
230 V AC / 15 VA / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250-K (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.120.07

1.1.31	Chain drive - VCD 204/250-K (WH)
230 V AC / 15 VA / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250-K (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.32	Chain drive - VCD 204/350-K (SR)
230 V AC / 15 VA / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-K (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.120.10

1.1.33	Chain drive - VCD 204/350-K (BK)
230 V AC / 15 VA / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-K (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.120.12

1.1.34	Chain drive - VCD 204/350-K (WH)
230 V AC / 15 VA / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-K (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.35	Chain drive - VCD 204-K - freely configurable
230 V AC / 15 VA / 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm / 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: on request
Colour: on request
Connection: PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204-K
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.120.00

1.1.36	Extension functions VCD 204-K
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.37	Chain drive - VCD 204/350-K-TMS+-B (SR)
230 V AC / 15 VA / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 2.5 m PVC connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-K-TMS+-B (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.121.25

1.1.38	Chain drive - VCD 204/350-Z-TMS+-A (SR)
24 V DC / 0.35 A / 200 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. 
 
Technical data:
Operating voltage: 24 V DC / ±20 %
Current consumption: 0.35 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit with 1.2 m connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: Chain drive - 
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.121.35

1.1.39	Chain drive set - VCD 204/250-K-TMS+ Set (SR)
230 V AC / 2x 15 VA / 2x 200 N / 250 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units with 2.5 m PVC connection cable with system plug, 1.2 m connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250-K-TMS+ Set (SR)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.40	Chain drive set - VCD 204/250-K-TMS+ Set (BK)
230 V AC / 2x 15 VA / 2x 200 N / 250 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units with 2.5 m PVC connection cable with system plug, 1.2 m connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250-K-TMS+ Set (BK)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.41	Chain drive set - VCD 204/250-K-TMS+ Set (WH)
230 V AC / 2x 15 VA / 2x 200 N / 250 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units with 2.5 m PVC connection cable with system plug, 1.2 m connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/250-K-TMS+ Set (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.42	Chain drive set - VCD 204/350-K-TMS+ Set (SR)
230 V AC / 2x 15 VA / 2x 200 N / 350 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Silver (~ RAL 9006)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units with 2.5 m PVC connection cable with system plug, 1.2 m connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-K-TMS+ Set (SR)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.43	Chain drive set - VCD 204/350-K-TMS+ Set (BK)
230 V AC / 2x 15 VA / 2x 200 N / 350 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: Black (~ RAL 9005)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units with 2.5 m PVC connection cable with system plug, 1.2 m connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-K-TMS+ Set (BK)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.44	Chain drive set - VCD 204/350-K-TMS+ Set (WH)
230 V AC / 2x 15 VA / 2x 200 N / 350 mm stroke
 
Performance features:
2 electromotive drive units, as a set, for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
Connection: 2.5 m PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
2 drive units with 2.5 m PVC connection cable with system plug, 1.2 m connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204/350-K-TMS+ Set (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.45	Chain drive set - VCD 204-K/-Z-TMS+ - freely configurable
230 V AC / 2x 15 VA / 2x 200 N / 250 mm stroke
 
Performance features:
Electromotive drive unit, (as set of 2 possible), for opening and closing of windows and flaps for daily ventilation. The drive is equipped with motor electronics controlled via microprocessor. TMS+" tandem safety function for operating 2 drives on one sash. Learning with magnet will be transmitted to dual drive. Option of chain stroke programming via magnet. The drive is equipped with a special chain stabilisation and centred chain outlet. Cut-off force in CLOSED-direction is electronically reduced to 150 N at the factory. Running speed in CLOSED direction decreases to 5 mm/s (passive closing edge protection). Time-controlled reversing when an obstacle is detected in the CLOSED direction (active closing edge protection). Electronic limit stop and overload cut-off is integrated. Connection of the drives via connector and direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 - 60 Hz
Performance: 10 W / 15 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 200 N
Tensile force: 200 N
Nominal locking force **: 2000 N
Service life: 20000 double strokes *
Stroke length: 250 mm / 350 mm
OPEN running speed: 6 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 30
Emission sound pressure level: LpA ≤ 46 dB(A)
Temperature range: 0 °C till +60 °C
Drive: Push link chain
Housing: Die-cast zinc
Surface: on request
Colour: on request
Connection: PVC-cable
Dimensions (WxHxD): 480 x 30 x 47 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
 
Scope of supply:
Drive unit(s) with PVC connection cable with system plug, connecting cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: VCD 204-K/-Z-TMS+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.121.00

1.1.46	Extension functions VCD 204-K-/Z-TMS+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.47	VCD-BS010-VFO - for Schüco® AWS 57 RO + RS 88D
VCD bracket set, outward opening
 
Performance features:
For mounted installation of VCD-S chain drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 RO, RS 88D;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Zinc
Suface: Powder-coated
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS010-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAK.KS

1.1.48	VCD-BS014-VFO - for Reynaers® CR 120
VCD bracket set, outward opening
 
Performance features:
For mounted installation of VCD-S chain drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CR 120;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver
 
Frame bracket
Material: V2A stainless steel
Colour: Silver (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS014-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAE.KS

1.1.49	VCD-BS015-VFO - for Schüco® RS 106D
VCD bracket set, outward opening
 
Performance features:
For mounted installation of VCD-S chain drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® S 106D;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS015-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAF.KS

1.1.50	VCD-BS016-VFO - for Schüco® RS 47D
VCD bracket set, outward opening
 
Performance features:
For mounted installation of VCD-S chain drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® RS 47D;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Zinc
Suface: Powder-coated
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS016-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAG.KS

1.1.51	VCD-BS017-VSI (SR) - for Raico® FRAME+ 75 + 90 WI
VCD bracket set (SR), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives;
Suitable for inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75, 90 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Silver (~ RAL 9006)
 
Cover:
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS017-VSI (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAL.KS

1.1.52	VCD-BS017-VSI (BK) - for Raico® FRAME+ 75 + 90 WI
VCD bracket set (BK), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives;
Suitable for inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75, 90 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Black (~ RAL 9005)
 
Frame bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Black (~ RAL 9005)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS017-VSI (BK)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.53	VCD-BS017-VSI (WH) - for Raico® FRAME+ 75 + 90 WI
VCD bracket set (WH), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives;
Suitable for inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75, 90 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: White (~ RAL 9016)
 
Frame bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: White (~ RAL 9016)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS017-VSI (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.54	VCD-BS018-VFI (SR) - for Raico® FRAME+ 75 + 90 WI
VCD bracket set (SR), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75, 90 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver (~ RAL 9006)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS018-VFI (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAP.KS

1.1.55	VCD-BS018-VFI (BK) - for Raico® FRAME+ 75 + 90 WI
VCD bracket set (BK), Rframe mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75, 90 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Black (~ RAL 9005)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Black (~ RAL 9005)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS018-VFI (BK)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.56	VCD-BS018-VFI (WH) - for Raico® FRAME+ 75 + 90 WI
VCD bracket set (WH), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75, 90 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: White (~ RAL 9016)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS018-VFI (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.57	VCD-BS019-VFO (SR) - for Raico® FRAME+ 75 WA
VCD bracket set (SR), Frame mounting, outward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 WA;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Passivated
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
Colour: Silver (~ RAL 9006)
 
Cover
Material: Plastic
 
Scope of supply
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS019-VFO (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAT.KS

1.1.58	VCD-BS019-VFO (BK) - for Raico® FRAME+ 75 WA
VCD bracket set (BK), Frame mounting, outward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 WA;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Passivated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
Colour: White (~ RAL 9016)
 
Cover
Material: Plastic
 
Scope of supply
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS019-VFO (BK)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.59	VCD-BS019-VFO (WH) - for Raico® FRAME+ 75 WA
VCD bracket set (WH), Frame mounting, outward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 WA;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Passivated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
Colour: White (~ RAL 9016)
 
Cover
Material: Plastic
 
Scope of supply
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS019-VFO (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.60	VCD-BS011-VFO (SR) - for Roto® R6, R8 + Velux® GGU/GGP/GPU/GPL/GHU/GHL
VCD bracket set (SR)
 
Performance features:
For mounted installation of VCD chain drives designed for roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers:
Roto®
- R6
- R8
Velux®
- GGU/GGL horizontal pivot window
- GPU/GPL top-hung window / horizontal pivot window(30° opening angle)
- GHU/GHL top-hung window / horizontal pivot window (45° opening angle)
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled and powder-coated
Colour: Silver (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS011-VFO (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAB.KS

1.1.61	VCD-BS011-VFO (BK) - for Roto® R6, R8 + Velux® GGU/GGP/GPU/GPL/GHU/GHL
VCD bracket set (BK)
 
Performance features:
For mounted installation of VCD chain drives designed for roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers:
Roto®
- R6
- R8
Velux®
- GGU/GGL horizontal pivot window
- GPU/GPL top-hung window / horizontal pivot window (30° opening angle)
- GHU/GHL top-hung window / horizontal pivot window (45° opening angle)
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Black (~ RAL 9005)
 
Frame bracket
Material: Edelstahl V2A
Suface: Tumbled and powder-coated
Colour: Black (~ RAL 9005)
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS011-VFO (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAC.KS

1.1.62	VCD-BS011-VFO (WH) - for Roto® R6, R8 + Velux® GGU/GGP/GPU/GPL/GHU/GHL
VCD bracket set (WH)
 
Performance features:
For mounted installation of VCD chain drives designed for roof windowsr;
Bracket set optimised for installation on the window profile of the profile manufacturers:
Roto®
- R6
- R8
Velux®
- GGU/GGL horizontal pivot window
- GPU/GPL top-hung window / horizontal pivot window (30° opening angle)
- GHU/GHL top-hung window / horizontal pivot window (45° opening angle)
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled and powder-coated
Colour: White (~ RAL 9016)
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS011-VFO (WH)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAA.KS

1.1.63	VCD-BS001-VSI (SR) - universal
VCD bracket set (SR), sash mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the sash frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Silver (~ RAL 9006)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS001-VSI (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAB.KS

1.1.64	VCD-BS001-VSI (BK) - universal
VCD bracket set (BK), sash mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the sash frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Black (~ RAL 9005)
 
Frame bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Black (~ RAL 9005)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS001-VSI (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAA.KS

1.1.65	VCD-BS001-VSI (WH) - universal
VCD bracket set (WH), sash mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the sash frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: White (~ RAL 9016)
 
Frame bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: White (~ RAL 9016)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: VCD-BS001-VSI (WH)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAC.KS

1.1.66	VCD-BS004-VFI (SR) - universal
VCD bracket set (SR), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver (~ RAL 9006)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS004-VFI (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAE.KS

1.1.67	VCD-BS004-VFI (BK) - universal
VCD bracket set (BK), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Black (~ RAL 9005)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Black (~ RAL 9005)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS004-VFI (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAD.KS

1.1.68	VCD-BS004-VFI (WH) - universal
VCD bracket set (WH), frame mounting, inward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: White (~ RAL 9016)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: VCD-BS004-VFI (WH)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAF.KS

1.1.69	VCD-BS007-VFO (SR) - universal
VCD bracket set (SR), frame mounting, outward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames ;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Silver (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Silver (~ RAL 9006)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type:VCD-BS007-VFO (SR)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAH.KS

1.1.70	VCD-BS007-VFO (BK) - universal
VCD bracket set (BK), frame mounting, outward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames ;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: Black (~ RAL 9005)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: Black (~ RAL 9005)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type:VCD-BS007-VFO (BK)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAG.KS

1.1.71	VCD-BS007-VFO (WH) - universal
VCD bracket set (WH), frame mounting, outward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames ;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Suface: Passivated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
Colour: White (~ RAL 9016)
 
Cover
Material: Plastic
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type:VCD-BS007-VFO (WH)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.CAJ.KS

1.1.72	VCD-BS008-VFO - universal
VCD bracket set , frame mounting, outward opening
 
Performance features:
For mounted installation of VCD 203 / VCD 204 chain drives on inward opening windows with face-fitted sash frames ;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Zink
Suface: Powder-coated
 
Frame bracket
Material: V2A stainless steel
Suface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type:VCD-BS008-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.BAD.KS

Information Selection Guide

Technologie TMS+
Up to two drives can be connected together. The output of the BRV signal only occurs in the end positions - therefore no malfunction with locking drives or modules. During the teaching phase, the adjusted stroke is transmitted to the tandem drive via the TMS+ function.
 
 
Technologie ACB
Enables direct bus communication between the controller and the drive for, for example, control with perfect positioning or drive feedback. Communication is via the open source Modbus protocol, and it enables the drive to be combined with an ACB?capable control panel or enables it to be directly connected to higher-level controllers such as a building management system.
1.1.73	TMS+ chain drive - CDC-0252-0350-1-TMS+ -R
24 V DC / 0.6 A / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Chain drive equipped with microprocessor-controlled motor electronic;
Tandem safety function "TMS+" (combines TMS- and BRV-signal) for operation of two drives on a single sash;
Reprogrammed opening stroke is transmitted to the tandem drive;
Option of chain stroke programming via magnet;
Electronic limit stop and overload cut-off;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Drive functions, performance features, force, start of the opening and closing range and stroke via Powerline (PLP) or via D+H software SCS programmable;
By recognizing an obstacle in CLOSE direction time controlled reversing (active closing edge protection);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection via plug-type connector on the drive motor side;
Direct triggering of lock drive;
Direct triggering of end position module;
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Design: Right
Force of pressure: 250 N (note pressure load diagram)
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed-SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 405 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-1-TMS+ -R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.109.10

1.1.74	TMS+ chain drive - CDC-0252-0600-1-TMS+ -R
24 V DC / 0.8 A / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Chain drive equipped with microprocessor-controlled motor electronic;
Tandem safety function "TMS+" (combines TMS- and BRV-signal) for operation of two drives on a single sash;
Reprogrammed opening stroke is transmitted to the tandem drive;
Option of chain stroke programming via magnet;
Electronic limit stop and overload cut-off;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Drive functions, performance features, force, start of the opening and closing range and stroke via Powerline (PLP) or via D+H software SCS programmable;
By recognizing an obstacle in CLOSE direction time controlled reversing (active closing edge protection);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection via plug-type connector on the drive motor side;
Direct triggering of lock drive;
Direct triggering of end position module;
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Design: Right
Force of pressure: 250 N (note pressure load diagram)
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed-SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 530 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-1-TMS+ -R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.109.20

1.1.75	TMS+ chain drive - CDC-0252-0800-1-TMS+ -R
24 V DC / 1 A / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Chain drive equipped with microprocessor-controlled motor electronic;
Tandem safety function "TMS+" (combines TMS- and BRV-signal) for operation of two drives on a single sash;
Reprogrammed opening stroke is transmitted to the tandem drive;
Option of chain stroke programming via magnet;
Electronic limit stop and overload cut-off;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Drive functions, performance features, force, start of the opening and closing range and stroke via Powerline (PLP) or via D+H software SCS programmable;
By recognizing an obstacle in CLOSE direction time controlled reversing (active closing edge protection);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection via plug-type connector on the drive motor side;
Direct triggering of lock drive;
Direct triggering of end position module;
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Design: Right
Force of pressure: 250 N (note pressure load diagram)
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed-SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-1-TMS+ -R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.109.30

1.1.76	ACB chain drive - CDC-0252-0350-1-ACB M1-R
24 V DC / 0.6 A / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/ s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 405 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.05

1.1.77	ACB chain drive - CDC-0252-0350-1-ACB M1-L
24 V DC / 0.6 A / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/ s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 405 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-1-ACB M1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.10

1.1.78	ACB chain drive - CDC-0252-0350-1-ACB M2-R
24 V DC / 0.6 A / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/ s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 405 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.06

1.1.79	ACB chain drive - CDC-0252-0350-1-ACB S1-L
24 V DC / 0.6 A / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/ s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 405 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.11

1.1.80	ACB chain drive - CDC-0252-0500-1-ACB M1-R
24 V DC / 0.8 A / 250 N / 500 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 485 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0500-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.55

1.1.81	ACB chain drive - CDC-0252-0500-1-ACB M1-L
24 V DC / 0.8 A / 250 N / 500 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 485 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0500-1-ACB M1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.60

1.1.82	ACB chain drive - CDC-0252-0500-1-ACB M2-R
24 V DC / 0.8 A / 250 N / 500 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 485 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0500-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.56

1.1.83	ACB chain drive - CDC-0252-0500-1-ACB S1-L
24 V DC / 0.8 A / 250 N / 500 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 485 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0500-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.61

1.1.84	ACB chain drive - CDC-0252-0600-1-ACB M1-R
24 V DC / 0.8 A / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 530 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.101.05

1.1.85	ACB chain drive - CDC-0252-0600-1-ACB M1-L
24 V DC / 0.8 A / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 530 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-1-ACB M1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.101.10

1.1.86	ACB chain drive - CDC-0252-0600-1-ACB M2-R
24 V DC / 0.8 A / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 530 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.101.06

1.1.87	ACB chain drive - CDC-0252-0600-1-ACB S1-L
24 V DC / 0.8 A / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 530 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.101.11

1.1.88	ACB chain drive - CDC-0252-0800-1-ACB M1-R
24 V DC / 1 A / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-1-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.102.05

1.1.89	ACB chain drive - CDC-0252-0800-1-ACB M1-L
24 V DC / 1 A / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-1-ACB M1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.102.10

1.1.90	ACB chain drive - CDC-0252-0800-1-ACB M2-R
24 V DC / 1 A / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-1-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.102.06

1.1.91	ACB chain drive - CDC-0252-0800-1-ACB S1-L
24 V DC / 1 A / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-1-ACB S1-L
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.102.11

1.1.92	ACB chain drive - CDC-1-ACB - freely configurable
24 V DC / Special production according to customer requirements
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption:
0.6 A (with 350 mm stroke)
0.8 A (with 500 + 600 mm stroke)
1 A (with 700 mm stroke)
1 A (with 800 - 1300 mm stroke)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Design: Right or Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm - 1300 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV:
9.4 mm/s (with 350 mm stroke)
13.6 mm/s (with 500 - 700 mm stroke)
15 mm/s (with 800 - 1300 mm stroke)
CLOSED running speed:
5 mm/s (with 350 mm stroke)
6.7 mm/s (with 500 - 700 mm stroke)
6.7 mm/s (with 800 - 1300 mm stroke)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: on request
Colour: on request
End caps, plug: Plastic
Connection: Silicone cable
Dimensions (WxHxD): 405-885 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-1-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.100.00

1.1.93	Extension functions CDC-0252-xxxx-1-ACB
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "ZB" -Drawbridge application for side installation of the drive on the window
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "KM" -Strong motor gearbox with increased power up to 400 N for opening and closing of heavy parallel opening and projected top-hung windows
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED"
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.94	ACB chain drive - CDC-TW-0502-0500-1-ACB
24 V DC / 1.6 A / 500 N / 500 mm stroke
 
Drive for the mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 500 N
Tensile force: 500 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 6.7 mm/ s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 1265 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-TW-0502-0500-1-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.95	ACB chain drive - CDC-TW-0502-0800-1-ACB
24 V DC / 2 A / 500 N / 800 mm stroke
 
Drive for the mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 500 N
Tensile force: 500 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 6.7 mm/ s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 1265 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-TW-0502-0800-1-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.96	ACB chain drive - CDC-TW-1-ACB - freely configurable
24 V DC / Special production according to customer requirements
 
Drive for the mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption:
1.2 A (with 350 mm stroke)
1.6 A (with 500 + 600 mm stroke)
2 A (with 700 + 800 mm stroke)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 500 N
Tensile force: 500 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm - 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV:
13.6 mm/s (with 350 - 600 mm stroke)
15 mm/s (with 700 + 800 mm stroke)
CLOSED running speed: 6.7 mm/ s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: on request
Colour: on request
End caps, plug: Plastic
Connection: Silicone cable
Dimensions (WxHxD): 805-1265 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-TW-1-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.103.00

1.1.97	Extension functions CDC-TW-0502-xxxx-1-ACB
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "KM" -Strong motor gearbox with increased power up to 400 N for opening and closing of heavy parallel opening and projected top-hung windows
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.98	ACB chain drive - CDC-0252-0350-5-ACB M1-R
230 V AC / 45 VA / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 33 W / 45 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/ s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 545 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-5-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.105.05

1.1.99	ACB chain drive - CDC-0252-0350-5-ACB M2-R
230 V AC / 90 VA / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 64 W / 90 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/ s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 545 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-5-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.105.06

1.1.100	ACB chain drive - CDC-0252-0350-1-ACB S1-L ON
24 V DC / 0.6 A / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. 24 V DC version in conjunction with the 230 V AC drive (Main 2).
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Due to loop-through option (DS) a connection with D+H locking drives is possible as well as an open bus communication via ACB (Advanced Communication Bus) e.g. in a building management system (building automation);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/ s (according to protection class 3, Machinery Directive 2006/42/EG)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 545 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-1-ACB S1-L ON
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.105.11

1.1.101	ACB chain drive - CDC-0252-0500-5-ACB M1-R
230 V AC / 45 VA / 250 N / 500 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 33 W / 45 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 625 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0500-5-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.105.55

1.1.102	ACB chain drive - CDC-0252-0500-5-ACB M2-R
230 V AC / 90 VA / 250 N / 500 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 64 W / 90 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 625 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0500-5-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.105.56

1.1.103	ACB chain drive - CDC-0252-0500-1-ACB S1-L ON
24 V DC / 0.8 A / 250 N / 500 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. 24 V DC version in conjunction with the 230 V AC drive (Main 2).
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Due to loop-through option (DS) a connection with D+H locking drives is possible as well as an open bus communication via ACB (Advanced Communication Bus) e.g. in a building management system (building automation);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 500 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6,7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 625 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0500-1-ACB S1-L ON
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.105.61

1.1.104	ACB chain drive - CDC-0252-0600-5-ACB M1-R
230 V AC / 45 VA / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 33 W / 45 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 670 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-5-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.106.05

1.1.105	ACB chain drive - CDC-0252-0600-5-ACB M2-R
230 V AC / 90 VA / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 64 W / 90 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 670 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-5-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.106.06

1.1.106	ACB chain drive - CDC-0252-0600-1-ACB S1-L ON
24 V DC / 0.8 A / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. 24 V DC version in conjunction with the 230 V AC drive (Main 2).
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Due to loop-through option (DS) a connection with D+H locking drives is possible as well as an open bus communication via ACB (Advanced Communication Bus) e.g. in a building management system (building automation);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6,7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 670 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-1-ACB S1-L ON
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.106.11

1.1.107	ACB chain drive - CDC-0252-0800-5-ACB M1-R
230 V AC / 45 VA / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 33 W / 45 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 775 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-5-ACB M1-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.107.05

1.1.108	ACB chain drive - CDC-0252-0800-5-ACB M2-R
230 V AC / 90 VA / 250 N / 800 mm Hub
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 64 W / 90 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 775 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-5-ACB M2-R
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.107.06

1.1.109	ACB chain drive - CDC-0252-0800-1-ACB S1-L ON
24 V DC / 1 A / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. 24 V DC version in conjunction with the 230 V AC drive (Main 2).
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Due to loop-through option (DS) a connection with D+H locking drives is possible as well as an open bus communication via ACB (Advanced Communication Bus) e.g. in a building management system (building automation);
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 800 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 775 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-1-ACB S1-L ON
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.107.11

1.1.110	ACB chain drive - CDC-5-ACB - freely configurable
230 V AC / Special production according to customer requirements
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Perfectly suited for smoke exhaust (SHEV), as well as for natural ventilation. Can be combined with D+H locking drives. Sub 1 as 24 V DC version in conjunction with the 230 V AC drive (Main 2).
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running 2 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in one more drive;
Easy installation thanks to s polarity reversal protection connector system;
Custom configuration possible via D+H software SCS;
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data - Main:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 33 W / 45 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1 or Main 2
Design: Right
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm - 1000 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV:
9.4 mm/s (with 350 mm stroke)
13.6 mm/s (with 500 - 700 mm stroke)
15 mm/s (with 800 - 1000 mm stroke)
CLOSED running speed:
5 mm/s (with 350 mm stroke)
6.7 mm/s (with 500 - 700 mm stroke)
6.7 mm/s (with 800 - 1000 mm stroke)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: on request
Colour: on request
End caps, plug: Plastic
Connection: Silicone cable
Dimensions (WxHxD): 545-870 x 30 x 39 mm
 
Technical data - Sub:
Operating voltage: 24 V DC / ±15 %
Current consumption:
0.6 A (with 350 mm stroke)
0.8 A (with 500 + 600 mm stroke)
1 A (with 700 - 1000 mm stroke)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub
Design: Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm - 1300 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV:
9.4 mm/s (with 350 mm stroke)
13.6 mm/s (with 500 - 700 mm stroke)
15 mm/s (with 800 - 1000 mm stroke)
CLOSED running speed:
5 mm/s (with 350 mm stroke)
6.7 mm/s (with 500 - 700 mm stroke)
6.7 mm/s (with 800 - 1000 mm stroke)
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range: -5 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: on request
Colour: on request
End caps, plug: Plastic
Connection: Silicone cable
Dimensions (WxHxD): 545-870 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-5-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.105.00

1.1.111	Extension functions CDC-0252-xxxx-5-ACB
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "DS" -Loop-through option enables connection with D+H locking drives and open bus communication via ACB
	Option "ZB" -Drawbridge application for side installation of the drive on the window
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "KM" -Strong motor gearbox with increased power up to 400 N for opening and closing of heavy parallel opening and projected top-hung windows
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible (only in connection with option "DS")
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.112	CDC-BS001-IFI - for wooden window frame IV 68/78/92
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives;
Suitable for wooden window frame profiles (IV 68, IV 78, IV 92);
For inward opening bottom-hung windows with face-fitted sash frames on the room side;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Tumbled, coated with Delta-Protekt®
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB001 (25.AAE.KS)
1x Frame bracket CDC-FB001 (25.AAD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS001-IFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AAA.KS

1.1.113	CDC-BS010-IFI - for wooden window frame IV 56/63/68/78/88/98
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives;
Suitable for wooden window frame profiles (IV56, IV63, IV68,IV78, IV88, IV98);
For inward opening windows with face-fitted sash frame on the room side, with 9 mm groove axis;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible Fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Brush finished, sealed with clear lacquer
 
Frame bracket
Material: Steel
Surface: Tumbled, coated with Delta-Protekt®
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB009 (25.ABG.KS)
1x Frame bracket CDC-FB001 (25.AAD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS010-IFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ABF.KS

1.1.114	CDC-BS025-IFI - for Reynaers® CS 68, CS 77
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CS 68, CS 77;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP013 (25.ACP.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS025-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.115	CDC-BS027-IFI - for Reynaers® CS 59
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CS 59;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP014 (25.ACR.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS027-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.116	CDC-BS029-IFI - for Reynaers® Eco
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Eco;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP017 (25.ACU.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS029-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.117	CDC-BS031-IFI - for Reynaers® CS 86-HI
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CS 86-HI;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP019 (25.ACW.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS031-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.118	CDC-BS033-IFI - for Heroal® 065, 065.i, 065.1, 065i.1, 110E
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 065, 065.i, 065.1, 065i.1, 110E;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB014 (25.ADG.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP021 (25.ADJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS033-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.119	CDC-BS034-IFI - for Schüco® AWS xx + Royal S xx.HI
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 65, 70HI, 70 BS.HI, 70 WF.HI, 75 SI, 75 BS.HI, Royal S xx.HI;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible Fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB015 (25.ADM.KS)
1x Frame bracket CDC-FB002(25.AAG.KS)
1x Cover plate CDC-CP001 (25.AAH.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS034-IFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ADN.KS

1.1.120	CDC-BS043-IFI - for Wicona® WICLINE 65 + 77
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 65 + 77;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB017 (25.ADZ.KS)
1x Frame bracket CDC-FB003 (25.AAN.KS)
1x Cover plate CDC-CP003 (25.AAP.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS043-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : d

1.1.121	CDC-BS045-IFI - for Wicona® WICLINE 60E + 70E
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 60E + 70E;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB018 (25.AEA.KS)
1x Frame bracket CDC-FB003 (25.AAN.KS)
1x Cover plate CDC-CP003 (25.AAP.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS045-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.122	CDC-BS047-IFI - for Hueck® 1.0
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB019 (25.AEB.KS)
1x Frame bracket CDC-FB004 (25.AAV.KS)
1x Cover plate CDC-CP004 (25.AAW.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS047-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.123	CDC-BS049-IFI - for Hueck® 72E
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 72E;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB020 (25.AEC.KS)
1x Frame bracket CDC-FB005 (25.AAZ.KS)
1x Cover plate CDC-CP005 (25.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS049-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.124	CDC-BS051-IFI - for Alcoa-Kawneer® AA 610 / 720
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Alcoa-Kawneer® AA 610 / 720;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Powder coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB021 (25.AED.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP003 (25.AAP.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS051-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.125	CDC-BS053-IFI - for Gutmann® S 70
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S 70;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB012 (25.ACL.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP003 (25.AAP.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS053-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.126	CDC-BS055-IFI - for Aluprof® MB-59S
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-59S;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP023 (25.AEX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS055-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.127	CDC-BS057-IFI - for Sykon® 70 + 75
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Sykon® 70 + 75;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Coated
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB023 (25.AFP.KS)
1x Frame bracket CDC-FB013 (25.AFT.KS)
1x Cover plate CDC-CP027 (25.AFR.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS057-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.128	CDC-BS059-IFI - for Sapa® SFB 1074
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 1074;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB022 (25.AFB.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP025 (25.AFC.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS059-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.129	CDC-BS062-IFI - for Raico® FRAME+
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Powder coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB024 (25.AFY.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP003 (25.AAP.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS062-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.130	CDC-BS067-IFI - for Heroal® 110ES
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 110ES;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed; ;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB024 (25.AFY.KS)
1x Frame bracket CDC-FB002 (25.AAG.KS)
1x Cover plate CDC-CP001 (25.AAH.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS067-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.131	CDC-BS072-IFI - for Aluprof® MB-60
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-60;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP029 (25.AGG.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS072-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.132	CDC-BS074-IFI - for Aluprof® MB-70
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-70;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP025 (25.AFC.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS074-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.133	CDC-BS078-IFI - for Wicona® WICLINE 65 + 75 EVO
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 65 + 75 EVO;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Coated with Delta-Protekt®
Colour: Black
 
Frame bracket
Material: Aluminium, stainless steel
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Cover plate
Material: Steel
Surface: Powder coated
Colour. Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB028 (25.AGU.KS)
1x Frame bracket CDC-FB017 (25.AGV.KS)
1x Cover plate CDC-CP031 (25.AGW.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS078-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.134	CDC-BS082-IFIS - for Wicona® WICLINE 65 + 75 EVO
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 65 und 75 EVO;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible Fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Cover plate
Material: Aluminium
Surface: Powder-coated
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB027 (25.AGT.KS)
1x Frame bracket CDC-FB017 (25.AGV.KS)
1x Cover plate CDC-CP031 (25.AGW.KS)
Including all necessary fastening materialsl
 
Brand: D+H Mechatronic AG
Type: CDC-BS082-IFIS
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.135	CDC-BS092-IFI - for Schüco® Corona SI
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on inward opening windows with with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Corona SI;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB029 (25.AHT.KS)
1x Frame bracket CDC-FB020 (25.AHO.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS092-IFI (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.136	CDC-BS094-IFI - for wooden window frame
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives;
Suitable for wooden window frame profiles with inward opening windows and face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: Aluminium
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB029 (25.AHT.KS)
1x Frame bracket CDC-FB022 (25.AHR.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS094-IFI (WH)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AHM.KS

1.1.137	CDC-BS001-IFI - for wooden window frame IV 68/78/92
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives;
Suitable for wooden window frame profiles (IV 68, IV 78, IV 92);
For inward opening bottom-hung windows with face-fitted sash frames on the room side;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Tumbled, coated with Delta-Protekt®
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB001 (25.AAE.KS)
1x Frame bracket CDC-FB001 (25.AAD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS001-IFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AAA.KS

1.1.138	CDC-BS010-IFI - for wooden window frame IV 56/63/68/78/88/98
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives;
Suitable for wooden window frame profiles (IV56, IV63, IV68,IV78, IV88, IV98);
For inward opening windows with face-fitted sash frame on the room side, with 9 mm groove axis;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible Fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Brush finished, sealed with clear lacquer
 
Frame bracket
Material: Steel
Surface: Tumbled, coated with Delta-Protekt®
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB009 (25.ABG.KS)
1x Frame bracket CDC-FB001 (25.AAD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic
Type: CDC-BS010-IFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ABF.KS

1.1.139	CDC-BS026-IFI - for Reynaers® CS 68, CS 77
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CS 68, CS 77;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP015 (25.ACS.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS026-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.140	CDC-BS028-IFI - for Reynaers® CS 59
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CS 59;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP016 (25.ACT.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS028-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.141	CDC-BS030-IFI - for Reynaers® Eco
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Eco;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP018 (25.ADV.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS030-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.142	CDC-BS032-IFI - for Reynaers® CS 86-HI
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CS 86-HI;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP020 (25.ACX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS032-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.143	CDC-BS035-IFI - for Schüco® AWS xx + Royal S xx.HI
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 65, 70HI, 70 BS.HI, 70 WF.HI, 75 SI, 75 BS.HI, Royal S xx.HI;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible Fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB015 (25.ADM.KS)
1x Frame bracket CDC-FB002 (25.AAG.KS)
1x Cover plate CDC-CP006 (25.ABH.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS035-IFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ADP.KS

1.1.144	CDC-BS039-IFI - for Heroal® 065, 065.i, 065.1, 065i.1, 110E
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 065, 065.i, 065.1, 065i.1, 110E;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB014 (25.ADG.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP022 (25.ADK.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS039-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.145	CDC-BS044-IFI - for Wicona® WICLINE 65 + 77
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 65 + 77;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB017 (25.ADZ.KS)
1x Frame bracket CDC-FB003 (25.AAN.KS)
1x Cover plate CDC-CP007 (25.ABJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS044-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.146	CDC-BS046-IFI - for Wicona® WICLINE 60E + 70E
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 60E + 70E;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB018 (25.AEA.KS)
1x Frame bracket CDC-FB003 (25.AAN.KS)
1x Cover plate CDC-CP007 (25.ABJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS046-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.147	CDC-BS048-IFI - for Hueck® 1.0
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB019 (25.AEB.KS)
1x Frame bracket CDC-FB004 (25.AAV.KS)
1x Cover plate CDC-CP009 (25.ABL.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS048-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.148	CDC-BS050-IFI - for Hueck® 72E
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 72E;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium(~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Painted
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB020 (25.AEC.KS)
1x Frame bracket CDC-FB005 (25.AAZ.KS)
1x Cover plate CDC-CP008 (25.ABK.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS049-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.149	CDC-BS052-IFI - for Alcoa-Kawneer® AA 610 / 720
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Alcoa-Kawneer® AA 610 / 720;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Powder coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB021 (25.AED.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP007 (25.ABJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS052-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.150	CDC-BS054-IFI - for Gutmann® S 70
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S 70;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Powder coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB012 (25.ACL.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP007 (25.ABJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS054-IF
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.151	CDC-BS056-IFI - for Aluprof® MB-59S
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-59S;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Powder coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP024 (25.AEY.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS056-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.152	CDC-BS058-IFI - for Sykon® 70 + 75
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Sykon® 70 + 75;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Coated
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB023 (25.AFP.KS)
1x Frame bracket CDC-FB013 (25.AFT.KS)
1x Cover plate CDC-CP028 (25.AFS.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS058-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.153	CDC-BS060-IFI - for Sapa® SFB 1074
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 1074;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB022 (25.AFB.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP026 (25.AFD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS060-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.154	CDC-BS063-IFI - for Raico® FRAME+
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Powder coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB024 (25.AFY.KS)
1x Frame bracket CDC-FB007 (25.ABW.KS)
1x Cover plate CDC-CP007 (25.ABJ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS063-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.155	CDC-BS068-IFI - for Heroal® 110ES
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 110ES;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed; ;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Steel
Surface: Coated with Delta-Protekt®
Colour: Black
 
Cover plate
Material: Steel
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB024 (25.AFY.KS)
1x Frame bracket CDC-FB002 (25.AAG.KS)
1x Cover plate CDC-CP006 (25.ABH.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS068-IFII
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.156	CDC-BS073-IFI - for Aluprof® MB-60
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-60;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP030 (25.AGH.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS073-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.157	CDC-BS075-IFI - for Aluprof® MB-70
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-70;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Aluminium
Surface: Painted
Colour: Black
 
Cover plate
Material: Aluminium
Surface: Coated
Colour: Black
 
Scope of supply
Set contents:
1x Sash bracket CDC-SB013 (25.ACM.KS)
1x Frame bracket CDC-FB010 (25.ACN.KS)
1x Cover plate CDC-CP026 (25.AFD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS075-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.158	CDC-BS079-IFI - for Wicona® WICLINE 65 + 75 EVO
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 65 + 75 EVO;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Coated with Delta-Protekt®
Colour: Black
 
Frame bracket
Material: Aluminium, stainless steel
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Cover plate
Material: Steel
Surface: Powder coated
Colour. Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB028 (25.AGU.KS)
1x Frame bracket CDC-FB017 (25.AGV.KS)
1x Cover plate CDC-CP032 (25.AGX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS079-IFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.159	CDC-BS083-IFIS - for Wicona® WICLINE 65 + 75 EVO
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 65 und 75 EVO;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area without visible Fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
Facing for covering of the integrated CDC drive;
 
Technical data:
Sash bracket
Material: Aluminium / V2A stainless steel
Surface: Anodized E6 / EV1 / powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Cover plate
Material: Aluminium
Surface: Powder-coated
Colour: Black
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB027 (25.AGT.KS)
1x Frame bracket CDC-FB017 (25.AGV.KS)
1x Cover plate CDC-CP032 (25.AGX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS083-IFIS
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.160	CDC-BS093-IFI - for Schüco® Corona SI
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on inward opening windows with with face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Corona SI;
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB029 (25.AHT.KS)
1x Frame bracket CDC-FB021 (25.AHQ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS093-IFI (WH)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.161	CDC-BS094-IFI - for wooden window frame
CDC bracket set, integrated installation in the window frame
 
Performance features:
For mounted installation of CDC drives of the 350 and 600 series;
Suitable for wooden window frame profiles with inward opening windows and face-fitted sash frames on the room side (for detailed information concerning profile compatibility please see D+H product sheet)
Minimum frame height 40 mm (on the room side);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed without visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Zinc
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Frame bracket
Material: Aluminium
Surface: Powder-coated
Colour: White (~ RAL 9016)
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB029 (25.AHT.KS)
1x Frame bracket CDC-FB022 (25.AHR.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS094-IFI (WH)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AHM.KS

1.1.162	CDC-BS080-VFO - for SAPA® SKF + PAF
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows with face-fitted sash frame;
Drive installation on the window frame (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: SAPA® SKF + PAF;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room sidel;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB008 (25.ABD.KS)
1x Frame bracket CDC-FB018 (25.AHA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS080-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.163	CDC-BS089-VFI - for Raico® FRAME+ 75 WI + 90 WI
CDC bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows with face-fitted sash frames;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 WI, 90 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
 
Frame bracket
Material: 2A stainless steelA
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDC-BS089-VFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AHG.KS

1.1.164	CDC-BS091-VSI - for Raico® FRAME+ 75 WI
CDC bracket set, mounted installation on the sash frame, inward opening
 
Performance features:
For mounted installation of CDC drives on inward opening windows with face-fitted sash frames;
Drive installation on the sash frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 WI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Die-cast aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDC-BS091-VSI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AHJ.KS

1.1.165	CDC-BS061-VFO - for Colt® Kameleon E
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: CDC-BS061-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.166	CDC-BS071-VFO - for Aluprof® MB-SR50
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-SR50;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: CDC-BS071-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.167	CDC-BS090-VFO - for Raico® FRAME+ 75 WA
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows with face-fitted sash frame;
Drive installation on the window frame;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 WA;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDC-BS090-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AHH.KS

1.1.168	BS-CDC-PAO-M-VSH
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC-0252-0800-1-ACB und CDC-0252-0800-1-TMS+ drives for an opening angle of up to 90° incl. one gas pressure spring;
Suitable for outward opening windows;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Gas pressure spring:
Force: 100 N
Material: Steel
 
Scope of supply:
Bracket set (incl. gas pressure spring) including all fastening material for installation.
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PAO-M-VSH
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.13

1.1.169	BS-CDC-PAO-M-VSH-WG
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of the second CDC-0252-0800-1-ACB und CDC-0252-0800-1-TMS+ drive (combine with 26.800.13) for an opening angle of up to 90°;
Suitable for outward opening windows;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PAO-M-VSH-WG
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.17

1.1.170	BS-CDC-PIO-M-VSH
CDC bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of CDC-0252-0800-1-ACB und CDC-0252-0800-1-TMS+ drives for an opening angle of up to 90° incl. one gas pressure spring;
Suitable for inward opening windows;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Gas pressure spring:
Force: 100 N
Material: Steel
 
Scope of supply:
Bracket set (incl. gas pressure spring) including all fastening material for installation.
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PIO-M-VSH
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.14

1.1.171	BS-CDC-PIO-M-VSH-WG
CDC bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of the second CDC-0252-0800-1-ACB und CDC-0252-0800-1-TMS+ drive (combine with 26.800.14) for an opening angle of up to 90°;
Suitable for inward opening windows;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PIO-M-VSH-WG
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.18

1.1.172	CDC-BS009-VFO - for Schüco® AWS 102
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 102;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB008 (25.ABD.KS)
1x Frame bracket CDC-FB006 (25.ABC.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS009-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ABE.KS

1.1.173	CDC-BS021-VFO - for Gutmann® S70 SK + Raico® WING 50 SK-R
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturers: Gutmann® S70 SK, Raico® WING 50 SK-R;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB008 (25.ABD.KS)
1x Frame bracket CDC-FB008 (25.ACF.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS021-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ACE.KS

1.1.174	CDC-BS038-VFO - for Reynaers® CW 50
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CW 50;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB016 (25.ADT.KS)
1x Frame bracket CDC-FB012 (25.ADU.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS038-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ADW.KS

1.1.175	CDC-BS064-VFO - for Skandinaviska® SG 2000
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Skandinaviska® SG 2000;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDC-BS064-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AGA.KS

1.1.176	CDC-BS065-VFO - for Raico® WING 50 SK-R
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 50 SK-R;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB008 (25.ABD.KS)
1x Frame bracket CDC-FB014 (25.AFU.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS065-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AFL.KS

1.1.177	CDC-BS069-VFO - for Sapa® SFB 1074
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 1074;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB025 (25.AGB.KS)
1x Frame bracket CDC-FB014 (25.AFU.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS069-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.178	CDC-BS070-VFO - for Sapa® SFB 1074 + additional profile
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 1074 + additional profile;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDC-SB025 (25.AGB.KS)
1x Frame bracket CDC-FB015 (25.AGD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDC-BS070-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.179	CDC-BS022 - for Velux® GGL + GGU
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 350 mm chain stroke on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Velux® GGL/GGU;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDC-BS022
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ACG.KS

1.1.180	CDC-BS023 - for Velux® GGL + GGU
CDC bracket set, integrated installation in the window frame
 
Performance features:
For integrated installation of CDC drives with up to 600 mm chain stroke on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Bracket set optimised for installation on the window profile of the profile manufacturer: Velux® GGL/GGU;
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDC-BS023
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.ACH.KS

1.1.181	BS-CDC-PI01-M-VFIS - top-hung bracket - universal
CDC bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of CDC drive 0252;
Suitable for standard window profiles with inward opening windows;
Drive installation on the window frame;
max. opening angle 60 degrees;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Stainless steel V2A
Surface: Tumbled
 
Frame bracket
Material: Stainless steel V2A
Surface: Tumbled
 
Special features:
- Drive CDC-0252 left or right must be installed with VCD chain end piece-A2
- Drive CDC-TW-0502 is not allowed for side-hung applications
- For side-hung and top-hung sash applications, the size and weight of the sash must be specified with myCalc
- For a bottom-hung sash application: use the CDC drive with a SBD side bow chain
 
Scope of delivery:
Bracket set including all fasteners required for installation.
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PI01-M-VFIS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.09

1.1.182	BS-CDC-PI01-O-VSI - universal
CDC bracket set, mounted installation on the sash, inward opening
 
Performance features:
For mounted installation of CDC drives on façade windows;
Suitable for window profiles with inward opening windows;
Drive installation on the sash frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Die-cast aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PI01-O-VSI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.02

1.1.183	BS-CDC-PI01-M-VFI - universal
CDC bracket set, mounted installation on the sash, inward opening
 
Performance features:
For mounted installation of CDC drives on façade windows;
Suitable for window profiles with inward opening windows;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PI01-M-VFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.01

1.1.184	CDC-BS066-VFI - universal
CDC bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For integrated installation of CDC drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Frame bracket
Material: Stainless steel A2
Surface: Tumbled
 
Sash bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: CDC-BS066-VFI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.185	CDC-BS077-VSI - universal
CDC bracket set, mounted installation on the sash frame, inward opening
 
Performance features:
For mounted installation of CDC drives on inward opening windows with face-fitted sash frames on the room side;
Drive installation on the sash frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: CDC-BS077-VSI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.186	BS-CDC-PA01-M-VFO - universal
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on façade windows;
Suitable for window profiles with outward opening windows;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: BS-CDC-PA01-M-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.800.03

1.1.187	CDC-BS076-VFO - universal
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows (for detailed information concerning profile compatibility please see D+H product sheet);
Instructions for installation can be found in the D+H application drawings and product information.
 
Complete set consisting of:
Sash bracket designed for fitting in the rebate area with visible fastening material from the room side;
Decoupling of the chain also possible when the window is closed;
 
Technical data:
Sash bracket
Material: Die-cast aluminium
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDC-BS076-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 25.AGN.KS

1.1.188	CDC-BS088-VFO - universal
CDC bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of CDC drives on outward opening windows with face-fitted sash frames;
Drive installation on the window frame;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Die-cast aluminium
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: CDC-BS088-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

Information Auswahlhilfe

Technologie TMS+
Bis zu zwei Antriebe können zusammen geschaltet werden. Ausgabe der BRV-Meldung erfolgt nur in den Endlagen - dadurch keine Fehlfunktion mit Verriegelungsantrieben oder Modulen. Während der Anlernphase wird dem Tandemantrieb der eingestellte Hub über die TMS+ Funktion übertragen.
 
 
Technologie ACB
Ermöglicht die direkte Buskommunikation zwischen Steuerung und Antrieb für z.B. positionsgenaue Ansteuerungen oder Antriebsrückmeldungen. Die Kommunikation basiert auf einem offenen Modbus-Protokoll und erlaubt die Kombination mit ACB-fähiger Zentrale oder die direkte Anbindung an übergeordnete Steuerungen wie Gebäudeleittechnik.
1.1.189	TMS+ Kettenantrieb - CDC-0252-0350-1-TMS+ -R (FR)
24 V DC / 0.6 A / 250 N / 350 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Chain drive equipped with microprocessor-controlled motor electronic;
Tandem safety function "TMS+" (combines TMS- and BRV-signal) for operation of two drives on a single sash;
Reprogrammed opening stroke is transmitted to the tandem drive;
Option of chain stroke programming via magnet;
Electronic limit stop and overload cut-off;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Drive functions, performance features, force, start of the opening and closing range and stroke via Powerline (PLP) or via D+H software SCS programmable;
By recognizing an obstacle in CLOSE direction time controlled reversing (active closing edge protection);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection via plug-type connector on the drive motor side;
Direct triggering of lock drive;
Direct triggering of end position module;
Drive with extended cable monitoring (monitoring for short circuit, wire breakage and cable breakage);
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.6 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Design: Right
Force of pressure: 250 N (note pressure load diagram)
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed-SHEV: 9.4 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 405 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0350-1-TMS+ -R (FR)
 
Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes)

Unit : Stk
Artikelnr. : 26.110.30

1.1.190	TMS+ Kettenantrieb - CDC-0252-0600-1-TMS+ -R (FR)
24 V DC / 0.8 A / 250 N / 600 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Chain drive equipped with microprocessor-controlled motor electronic;
Tandem safety function "TMS+" (combines TMS- and BRV-signal) for operation of two drives on a single sash;
Reprogrammed opening stroke is transmitted to the tandem drive;
Option of chain stroke programming via magnet;
Electronic limit stop and overload cut-off;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Drive functions, performance features, force, start of the opening and closing range and stroke via Powerline (PLP) or via D+H software SCS programmable;
By recognizing an obstacle in CLOSE direction time controlled reversing (active closing edge protection);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection via plug-type connector on the drive motor side;
Direct triggering of lock drive;
Direct triggering of end position module;
Drive with extended cable monitoring (monitoring for short circuit, wire breakage and cable breakage);
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 0.8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Design: Right
Force of pressure: 250 N (note pressure load diagram)
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed-SHEV: 13.6 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 530 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0600-1-TMS+ -R (FR)
 
Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes)

Unit : Stk
Artikelnr. : 26.110.31

1.1.191	TMS+ Kettenantrieb - CDC-0252-0800-1-TMS+ -R (FR)
24 V DC / 1 A / 250 N / 800 mm stroke
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Chain drive equipped with microprocessor-controlled motor electronic;
Tandem safety function "TMS+" (combines TMS- and BRV-signal) for operation of two drives on a single sash;
Reprogrammed opening stroke is transmitted to the tandem drive;
Option of chain stroke programming via magnet;
Electronic limit stop and overload cut-off;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Drive functions, performance features, force, start of the opening and closing range and stroke via Powerline (PLP) or via D+H software SCS programmable;
By recognizing an obstacle in CLOSE direction time controlled reversing (active closing edge protection);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Easy installation thanks to s polarity reversal protection connector system;
Connection via plug-type connector on the drive motor side;
Direct triggering of lock drive;
Direct triggering of end position module;
Drive with extended cable monitoring (monitoring for short circuit, wire breakage and cable breakage);
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Design: Right
Force of pressure: 250 N (note pressure load diagram)
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 600 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed-SHEV: 15 mm/s
CLOSED running speed: 5 mm/s - 6.7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
End caps, plug: Plastic, grey (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-0252-0800-1-TMS+ -R (FR)
 
Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes)

Unit : Stk
Artikelnr. : 26.110.32

1.1.192	ACB chain drive - CDC-1-ACB (FR) - freely configurable
24 V DC / Special production according to customer requirements
 
Drive for the integrated, hidden installation in the window profile and for mounted installation. For the convenient motorised opening and closing of windows and flaps. Useable for smoke exhaust (SHEV), D+H Euro SHEV in accordance with EN 12101-2 as well as for natural ventilation. Can be combined with D+H locking drives.
 
Performance features:
Integrated, freely programmable electronic shut-down device to prevent a defect in the event of an overload on the window or drive;
Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol;
The drive is integrated directly via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation);
High precision synchronised electronics for running up to 8 drives simultaneously;
Low operating noises thanks to the innovative acoustic decoupling of the drive components;
Corrosion protected, hardened steel chain with rigid backing and lifetime lubrication;
High-speed function (HS) for opening windows especially fast in case of fire (SHEV);
Adjustable, multi-stage anti-trap protection system (runtime, force/power, stroke);
Gasket protection thanks to the automatic relief of pressure on window gasket after a closing process;
Low wiring effort with an option of looping in up to 3 drives;
Easy installation thanks to s polarity reversal protection connector system;
Connection from either the left or the right side is possible (supply includes BUS signals);
Custom configuration possible via D+H software SCS;
Drive with extended cable monitoring (monitoring for short circuit, wire breakage and cable breakage);
 
Functional description ACB
Secure SHEV-BUS communication via an encrypted data transfer between D+H Mechatronic AG control panels and drives.
Directly controlling the drive using the ACB is possible. The drive is set to the pole change operation at the factory by default.
Control with perfect positioning and feedback including information about the CURRENT position.
Status messages such as the drive´s OPEN and CLOSED signal are issued directly via ACB communication.
The general status of the drive, such as the total travel path, number of control units, diagnostics and the emergency drive function can be evaluated.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption:
0.6 A (with 350 mm stroke)
0.8 A (with 500 + 600 mm stroke)
1 A (with 700 mm stroke)
1 A (with 800 - 1300 mm stroke)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Design: Right or Left
Force of pressure: 250 N
Tensile force: 250 N
Nominal locking force **: 1500 N
Service life: 20000 double strokes *
Stroke length: 350 mm - 1300 mm / ±2 %
OPEN running speed: 6.7 mm/s
OPEN running speed - SHEV:
9.4 mm/s (with 350 mm stroke)
13.6 mm/s (with 500 - 700 mm stroke)
15 mm/s (with 800 - 1300 mm stroke)
CLOSED running speed:
5 mm/s (with 350 mm stroke)
6.7 mm/s (with 500 - 700 mm stroke)
6.7 mm/s (with 800 - 1300 mm stroke)
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 35 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Opening mechanic: Maintenance-free, corrosion protected hardened push linked chain with lifetime lubrication
Housing: Aluminium
Surface: on request
Colour: on request
End caps, plug: Plastic
Connection: Silicone cable
Dimensions (WxHxD): 405-885 x 30 x 39 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable with system plug, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDC-1-ACB (FR)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/fr/fr/services/conception-et-etudes)

Unit : Stk
Artikelnr. : 26.110.00

1.1.193	Extension functions CDC-0252-xxxx-1-ACB
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "ZB" -Drawbridge application for side installation of the drive on the window
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "KM" -Strong motor gearbox with increased power up to 400 N for opening and closing of heavy parallel opening and projected top-hung windows
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED"
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

Information Selection Guide

Technologie LIGHT (K)
LIGHT actuators (230 V AC) can only be controlled in OPEN and CLOSE direction.
 
 
Technologie PLP
Data transmission via the drive‘s connection cable. Drive characteristics can be programmed directly via the supply cable. Thus, no additional cable is required for parameterisation.
 
 
Technologie BSY+
BSY+ enables communication and synchronisation between different components in the window. For example between the chain drives, during synchronous operation, or between window and locking drives (e.g. FRA 11 BSY+ or VLD-BSY+). 
 
 
Technologie ACB
Enables direct bus communication between the controller and the drive for, for example, control with perfect positioning or drive feedback. Communication is via the open source Modbus protocol, and it enables the drive to be combined with an ACB?capable control panel or enables it to be directly connected to higher-level controllers such as a building management system.
1.1.194	PLP chain drive - KA 34/350
24 V DC / 1 A / 300 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 421 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/350
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.000.10

1.1.195	PLP chain drive - KA 34/500
24 V DC / 1 A / 300 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 496 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type KA 34/500
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.000.15

1.1.196	PLP chain drive - KA 34/600
24 V DC / 1 A / 300 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes **
Stroke length: 600 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 546 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type KA 34/600
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.000.20

1.1.197	PLP chain drive - KA 34/700
24 V DC / 1 A / 300 N / 700 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 700 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 596 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/700
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.000.25

1.1.198	PLP chain drive - KA 34/800
24 V DC / 1 A / 300 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 646 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/800
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.000.30

1.1.199	PLP chain drive - KA 34/1000
24 V DC / 1 A / 300 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 750 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/1000
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.000.35

1.1.200	PLP chain drive - KA 54/350
24 V DC / 1.4 A / 500 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 421 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/350
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.001.10

1.1.201	PLP chain drive - KA 54/500
24 V DC / 1.4 A / 500 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 496 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/500
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.001.15

1.1.202	PLP chain drive - KA 54/600
24 V DC / 1.4 A / 500 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 546 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/600
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.001.20

1.1.203	PLP chain drive - KA 54/700
24 V DC / 1.4 A / 500 N / 700 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 700 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 596 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/700
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.001.25

1.1.204	PLP chain drive - KA 54/800
24 V DC / 1.4 A / 500 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 646 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/800
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.001.30

1.1.205	PLP chain drive - KA 54/1000
24 V DC / 1.4 A / 500 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 750 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/1000
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.001.35

1.1.206	PLP chain drive - KA-PLP - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption:
1 A (KA 34)
1.4 A (KA 54)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
300 N (KA 34)
500 N (KA 54)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (KA 34)
500 N (KA 54)
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm - 1300 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV:
12.2 mm/s (KA 34)
13.3 mm/s (KA 54)
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable
Dimensions (WxHxD): 421-902 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA-PLP
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.000.00

1.1.207	Extension functions KA-PLP
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "BRV" -Signal for connection to FRA, VLD, ERM 44 or AT 41
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED"
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.208	BSY+ chain drive - KA 34/350-BSY+ R (M2)
24 V DC / 1 A / 300 N / 350 mm stroke
 
Performance features:
Electromotive drive unit forr mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 421 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/350-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.209	BSY+ chain drive - KA 34/350-BSY+L (S1)
24 V DC / 1 A / 300 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 421 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/350-BSY+ L (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.210	BSY+ chain drive - KA 34/500-BSY+ R (M2)
24 V DC / 1 A / 300 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 496 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/500-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.211	BSY+ chain drive - KA 34/500-BSY+ L (S1)
24 V DC / 1 A / 300 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 496 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/500-BSY+ L (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.212	BSY+ chain drive - KA 34/600-BSY+ R (M2)
24 V DC / 1 A / 300 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 546 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/600-BSY+ R (M2)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.21

1.1.213	BSY+ chain drive - KA 34/600-BSY+ L (S1)
24 V DC / 1 A / 300 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 546 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/600-BSY+ L (S1)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.22

1.1.214	BSY+ chain drive - KA 34/700-BSY+ R (M2)
24 V DC / 1 A / 300 N / 700 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 700 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 596 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/700-BSY+ R (M2)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.26

1.1.215	BSY+ chain drive - KA 34/700-BSY+ L (S1)
24 V DC / 1 A / 300 N / 700 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 700 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 596 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/700-BSY+ L (S1)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.27

1.1.216	BSY+ chain drive - KA 34/800-BSY+ R (M2)
24 V DC / 1 A / 300 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 646 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/800-BSY+ R (M2)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.31

1.1.217	BSY+ chain drive - KA 34/800-BSY+ L (S1)
24 V DC / 1 A / 300 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 646 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/800-BSY+ L (S1)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.32

1.1.218	BSY+ chain drive - KA 34/1000-BSY+ R (M2)
24 V DC / 1 A / 300 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 750 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/1000-BSY+ R (M2)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.36

1.1.219	BSY+ chain drive - KA 34/1000-BSY+ L (S1)
24 V DC / 1 A / 300 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 750 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/1000-BSY+ L (S1)
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.37

1.1.220	BSY+ chain drive - KA 54/350-BSY+ R (M2)
24 V DC / 1.4 A / 500 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 421 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/350-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.221	BSY+ chain drive - KA 54/350-BSY+ L (S1)
24 V DC / 1.4 A / 500 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 421 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/350-BSY+ L (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.222	BSY+ chain drive - KA 54/500-BSY+ R (M2)
24 V DC / 1.4 A / 500 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 496 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/500-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.223	BSY+ chain drive - KA 54/500-BSY+ L (S1)
24 V DC / 1.4 A / 500 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 496 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/500-BSY+ RL (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.224	BSY+ chain drive - KA 54/600-BSY+ R (M2)
24 V DC / 1.4 A / 500 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 546 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/600-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.225	BSY+ chain drive - KA 54/600-BSY+ L (S1)
24 V DC / 1.4 A / 500 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 546 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/600-BSY+ L (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.226	BSY+ chain drive - KA 54/700-BSY+ R (M2)
24 V DC / 1.4 A / 500 N / 700 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 700 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 596 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/700-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.227	BSY+ chain drive - KA 54/700-BSY+ L (S1)
24 V DC / 1.4 A / 500 N / 700 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 700 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 596 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/700-BSY+ L (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.228	BSY+ chain drive - KA 54/800-BSY+ R (M2)
24 V DC / 1.4 A / 500 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 646 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/800-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.229	BSY+ chain drive - KA 54/800-BSY+ L (S1)
24 V DC / 1.4 A / 500 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 646 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/800-BSY+ L (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.230	BSY+ chain drive - KA 54/1000-BSY+ R (M2)
24 V DC / 1.4 A / 500 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main 2
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 750 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/1000-BSY+ R (M2)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.231	BSY+ chain drive - KA 54/1000-BSY+ L (S1)
24 V DC / 1.4 A / 500 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 1.4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Sub 1
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 750 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Dive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/1000-BSY+ L (S1)
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.232	BSY+ chain drive - KA-BSY+ - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit, (as set up to 8 drives in one synchronous group possible), for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Power supply and BSY+ signals can be looped through the drives. The power supply can be connected either from left or right.
 
Technical data:
(per drive)
Operating voltage: 24 V DC / ±15 %
Current consumption:
1 A (KA 34)
1.4 A (KA 54)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main or Sub
Design: Right or Left
Force of pressure:
300 N (KA 34)
500 N (KA 54)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (KA 34)
500 N (KA 54)
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm - 1300 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV:
12.2 mm/s (KA 34)
13.3 mm/s (KA 54)
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable
Dimensions (WxHxD): 421-902 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit(s) with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.010.00

1.1.233	Extension functions KA-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "BRV" -Signal for connection to FRA, VLD, ERM 44 or AT 41
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.234	BSY+ chain drive set - KA-K-BSY+ Set - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
2 electromotive drive units, as a set, for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running at a window element. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance:
45 W / 75 VA (KA 34)
75 W / 115 VA (KA 54)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main or Sub
Design: Right or Left
Force of pressure:
300 N (KA 34)
500 N (KA 54)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (KA 34)
500 N (KA 54)
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm - 1300 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV:
12.2 mm/s (KA 34)
13.3 mm/s (KA 54)
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable
Dimensions (WxHxD): 560-1041 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
2 drive units with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA-K-BSY+ Set
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.007.00

1.1.235	Extension functions KA-K-BSY+ Set
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke (option "CP")
	Option "HP" -Stroke programming (option "HP")
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives (option "VP")
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s (option "LS")
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights (option SBD / SBU)
	Option "MA" -End position message "OPEN" (option "MA")
	Option "MZ" -End position message "CLOSED" (option "MZ")
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG (option "AS2")
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG (option "AS3")
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS (option "special colour")


Unit : Stk

1.1.236	BSY+ chain drive - KA 66/500-TW065
24 V DC / 2 A / 600 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+. Synchronous operation of two drive chains for optimum power application into the sash. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 600 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 600 N
Nominal locking force **: 3000 N
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Chain spacing: 650 mm
Dimensions (WxHxD): 997 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 66/500-TW065
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.237	BSY+ chain drive - KA 66/350-TW1
24 V DC / 2 A / 600 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+. Synchronous operation of two drive chains for optimum power application into the sash. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 600 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 600 N
Nominal locking force **: 3000 N
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Chain spacing: 1000 mm
Dimensions (WxHxD): 1347 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 66/350-TW1
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.238	BSY+ chain drive - KA 66/500-TW1
24 V DC / 2 A / 600 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+. Synchronous operation of two drive chains for optimum power application into the sash. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 600 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 600 N
Nominal locking force **: 3000 N
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Chain spacing: 1000 mm
Dimensions (WxHxD): 1347 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 66/500-TW1
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.239	BSY+ chain drive - KA 66/600-TW1
24 V DC / 2 A / 600 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+. Synchronous operation of two drive chains for optimum power application into the sash. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 600 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 600 N
Nominal locking force **: 3000 N
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Chain spacing: 1000 mm
Dimensions (WxHxD): 1347 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 66/600-TW1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.013.50

1.1.240	BSY+ chain drive - KA 66/800-TW1
24 V DC / 2 A / 600 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+. Synchronous operation of two drive chains for optimum power application into the sash. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 600 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 600 N
Nominal locking force **: 3000 N
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Chain spacing: 1000 mm
Dimensions (WxHxD): 1347 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 66/800-TW1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.013.60

1.1.241	BSY+ chain drive - KA-TW-BSY+ - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+. Synchronous operation of two drive chains for optimum power application into the sash. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 600 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 600 N
Nominal locking force **: 3000 N
Service life: 20000 double strokes *
Stroke length: 350 mm - 800 mm
OPEN running speed: 11.8 mm/s
OPEN running speed - SHEV: 12.2 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable
Chain spacing: 650 mm / 1000 mm
Dimensions (WxHxD): 997/1347 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA-TW-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.013.00

1.1.242	Extension functions KA-TW-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "BRV" -Signal for connection to FRA, VLD, ERM 44 or AT 41
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.243	BSY+ chain drive - KA-TW-K-BSY+ - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+. Synchronous operation of two drive chains for optimum power application into the sash. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. The power supply can be connected either from left or right. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 45 W / 75 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 600 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 600 N
Nominal locking force **: 3000 N
Service life: 20000 double strokes *
Stroke length: 350 mm - 800 mm
OPEN running speed: 12.2 mm/s
OPEN running speed - SHEV: 16.1 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable
Chain spacing: 650 mm / 1000 mm
Dimensions (WxHxD): 1275/1625 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 66-TW-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.014.00

1.1.244	Extension functions KA-TW-K-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "MA" -End position message "OPEN"
	Option "MZ" -End position message "CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.245	ACB chain drive - KA-ACB - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit, (up to 8 drives in one synchronous group possible), for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps with high weights. Integrated bus interface ACB (Advanced Communication Bus) with Modbus protocol. Direct integration of the drive through open bus communication via ACB (Advanced Communication Bus). Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet function in ventilation mode. Multi-stage anti-trap protection system regularly on board and via D+H software adjustable. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed.
 
 
Note: The following functional features are NOT possible:
- No KA-TW possible
- No looping through of the ACB at the drive possible
- No KA-K (230V version) possible
- Limited compatibility for connection to existing D+H central units. The restriction concerns the supply voltage. Residual ripple ≤ 2Vpp.
- Fast run only via ACB via the CPS-M or CPS-B
 
 
Technical data:
(per drive)
Operating voltage: 24 V DC / ±15 %
Current consumption:
1 A (KA 34)
1.4 A (KA 54)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main or Sub
Design: Right or Left
Force of pressure:
300 N (KA 34)
500 N (KA 54)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (KA 34)
500 N (KA 54)
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 250 mm - 1300 mm
OPEN running speed: 7 mm/s
OPEN running speed - SHEV:
12.2 mm/s (KA 34)
13.3 mm/s (KA 54)
CLOSED running speed: 7 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: 2,5 m - 12,5 m Silicone cable
Dimensions (WxHxD): 421-902 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit(s) with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.021.00

1.1.246	Erweiterungsfunktionen KA-ACB
	Option "HP" - Hub-Programmierung
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" - Low-Speed-Programmierung in ZU Richtung auf 5 mm/s
	Option "SBD/SBU" - Korrosionsgeschützte, gehärtete Stahlkette in Seitenbogenausführung für geringe Flügelhöhen
	Option "ZB" -Drawbridge application for side installation of the drive on the window"
	Option "Sonderfarbe" - Farbbeschichtung für perfekte Integration in die Fassadenoptik nach RAL, DB, NCS


Unit : Stk

1.1.247	Chain drive - KA 34/350-K
230 V AC / 40 VA / 300 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 24 W / 40 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 12.1 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 560 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/350-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.005.10

1.1.248	Chain drive - KA 34/500-K
230 V AC / 40 VA / 300 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 24 W / 40 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 12.1 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/500-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.005.15

1.1.249	Chain drive - KA 34/600-K
230 V AC / 40 VA / 300 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 24 W / 40 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 12.1 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 685 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/600-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.005.20

1.1.250	Chain drive - KA 34/700-K
230 V AC / 40 VA / 300 N / 700 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 24 W / 40 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 700 mm
OPEN running speed: 12.1 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 735 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/700-K
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.251	Chain drive - KA 34/800-K
230 V AC / 40 VA / 300 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 24 W / 40 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 12.1 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 785 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/800-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.005.30

1.1.252	Chain drive - KA 34/1000-K
230 V AC / 40 VA / 300 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 24 W / 40 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 300 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 300 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 12.1 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 889 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 34/1000-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.005.35

1.1.253	Chain drive - KA 54/350-K
230 V AC / 52 VA / 500 N / 350 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 32 W / 52 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm
OPEN running speed: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 560 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/350-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.002.05

1.1.254	Chain drive - KA 54/500-K
230 V AC / 52 VA / 500 N / 500 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 32 W / 52 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 500 mm
OPEN running speed: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 635 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/500-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.002.10

1.1.255	Chain drive - KA 54/600-K
230 V AC / 52 VA / 500 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 32 W / 52 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 600 mm
OPEN running speed: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 685 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/600-K
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.002.15

1.1.256	Chain drive - KA 54/800-K
230 V AC / 52 VA / 500 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 32 W / 52 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 800 mm
OPEN running speed: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 785 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/800-K
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.257	Chain drive - KA 54/1000-K
230 V AC / 52 VA / 500 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance: 32 W / 52 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 500 N (note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force: 500 N
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 1000 mm
OPEN running speed: 13.3 mm/s
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 889 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA 54/1000-K
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.258	Chain drive - KA-K - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile or sash profile. Drive for electromotive opening and closing of windows and flaps. The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are pre-installed at the factory (according to customer specification). Passive and active anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Particularly quiet function in daily ventilation mode. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / +10/-15 % / 50 Hz
Performance:
24 W / 40 VA (KA 34-K)
32 W / 52 VA (KA 54-K)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
300 N (KA 34-K)
500 N (KA 54-K)
(note pressure load diagram)
+ 20 % cut-off reserve (temporary)
Tensile force:
300 N (KA 34-K)
500 N (KA 54-K)
Nominal locking force **: Max. 2600 N (2000 N ***)
Service life: 20000 double strokes *
Stroke length: 350 mm - 1300 mm
OPEN running speed:
12.2 mm/s (KA 34)
13.3 mm/s (KA 54)
CLOSED running speed: 11.8 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C ***) till +75 °C
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable
Dimensions (WxHxD): 560-1041 x 40 x 59 mm
 
* For vertical use, please consult with D+H Sales!
** Depending on the mounting
*** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: KA-K
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.005.00

1.1.259	Extension functions KA-K
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SBD/SBU" -Corrosion protected, hardened steel chain in side bow design for low sash hights
	Option "MA" -End position message "OPEN"
	Option "MZ" -End position message "CLOSED"
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.260	KA-BS002-VFO - for Gutmann® S70 roof + Raico® WING 105D + Wicona® WICTEC 50/60
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Gutmann® S70 Dach, Raico® WING 105D, Wicona® WICTEC 50/60;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: KA-BS002-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AAJ.KS

1.1.261	KA-BS004-VFO - for Gutmann® S70 roof (wood)
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70 roof(wood);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium,
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: KA-BS004-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.262	KA-BS005-VFO - for Jet-Brakel Aero® Ventria TG
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Jet-Brakel Aero® Ventria TG;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB003 (26.AAW.KS)
1x Frame bracket KA-FB007 (26.AAU.KS)
Bracket set without fastening materials, these are provided by Jet Brakel Aero®.
 
Brand: D+H Mechatronic AG
Type: KA-BS005-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.263	KA-BS009-VFO - for Schüco® Royal S 88D
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 88D;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Material: V2A stainless steel
Colour: Silver
 
Frame bracket
Material: V2A stainless steel
Colour: Silver
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB004 (26.AAZ.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS009-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.264	KA-BS010-VFO - for Schüco® Royal S 106D
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 106D;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Colour: Silver
 
Frame bracket
Material: V2A stainless steel
Colour: Silver
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB005 (26.ABC.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS010-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.265	KA-BS011-VFO - for Heroal® 180
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB006 (26.ABH.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS011-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.266	KA-BS013-VFO - for Reynaers® CR 120
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CR 120;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB007 (26.ABL.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS013-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ABM.KS

1.1.267	KA-BS015-VFO - for Sapa® SFB 5050 + SFB 5060
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 5050, SFB 5060;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB008 (26.ABP.KS)
1x Frame bracket KA-FB009 (26.ABD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS015-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ABR.KS

1.1.268	KA-BS018-VFO - for Hueck® 85E
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB008 (26.ABP.KS)
1x Frame bracket KA-FB005 (26.AAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS018-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.269	KA-BS020-VFO - for Aluprof® MB-SR50 + Technal® MX
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-SR50, Technal® MX;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB009 (26.ABW.KS)
1x Frame bracket KA-FB010 (26.ABX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS020-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.270	KA-BS022-VFO - for Hueck® 1.0
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB006 (26.ABH.KS)
1x Frame bracket KA-FB010 (26.ABX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS022-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.271	KA-BS053-VFO - for Schüco® Royal 47D
KA bracket set, mounted installation, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal 47D;
The opening angle of the window must not exceed 30°;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Material: Steel V2A
 
Scope of supply:
Bracket set without fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS053-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.272	KA-BS062-VFO - for Schüco® AWS 57 RO
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 RO;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB010 (26.ADW.KS)
1x Frame bracket KA-FB013 (26.ADX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS062-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ADY.KS

1.1.273	KA-BS069-VFO - for Colt® Kameleon E
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB012 (26.AEE.KS)
1x Frame bracket KA-FB010 (26.ABX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS069-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.274	KA-BS080-VFO - for Reynaers® Flush Roof Vent
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB002 (26.AAS.KS)
1x Frame bracket KA-FB005 (26.AAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS080-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFE.KS

1.1.275	KA-BS087-VFO - for Wicona® WICLINE 65
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Wicona® WICLINE 65;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB002 (26.AAS.KS)
1x Frame bracket KA-FB017 (26.AFN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS087-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFP.KS

1.1.276	KA-BS090-VFO - for Heroal® 180ES
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180ES;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB001 (26.AAA.KS)
1x Frame bracket KA-FB018 (26.AFT.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS090-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.277	KA-BS096-VFO - for Aluprof® MB-RW
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB002 (26.AAS.KS)
1x Frame bracket KA-FB019 (26.AGC.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS096-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AGA.KS

1.1.278	KA-BS099-VFO - for Raico® FRAME+ 100/120RI
KA bracket set, mounted installation, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB015 (26.AGF.KS)
1x Frame bracket KA-FB020 (26.AGE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS099-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AGG.KS

1.1.279	KA-BS101-VFO - for Raico® FRAME+ 100/120RI-T
KA bracket set, mounted installation, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB016 (26.AGP.KS)
1x Frame bracket KA-FB021 (26.AGQ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS101-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AGL.KS

1.1.280	KA-TW-BS026-VFO - for Gutmann® S70 roof + Raico® WING 105D + Wicona® WICTEC 50/60
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70 Dach, Raico® WING 105D, Wicona® WICTEC 50/60;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB001 (26.AAA.KS)
1x Frame bracket KA-FB005 (26.AAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS026-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.281	KA-TW-BS027-VFO - for Schüco® Royal S 88D
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 88D;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Colour: Silver
 
Frame bracket
Material: V2A stainless steel
Colour: Silver
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB004 (26.AAZ.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS027-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.282	KA-TW-BS028-VFO - for Schüco® Royal S 106D
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® Royal S 106D;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Colour: Silver
 
Frame bracket
Material: V2A stainless steel
Colour: Silver
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB005 (26.ABC.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS028-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.283	KA-TW-BS029-VFO - for Heroal® 180
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB006 (26.ABH.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS029-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.284	KA-TW-BS030-VFO - for Reynaers® CR 120
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CR 120;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB007 (26.ABL.KS)
1x Frame bracket KA-FB008 (26.ABA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS030-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.285	KA-TW-BS031-VFO - for Sapa® SFB 5050 + SFB 5060
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 5050, SFB 5060;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Colour: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB008 (26.ABP.KS)
1x Frame bracket KA-FB009 (26.ABD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS031-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.286	KA-TW-BS032-VFO - for Jet-Brakel Aero® Ventria TG
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Jet-Brakel Aero® Ventria TG;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB003 (26.AAW.KS)
1x Frame bracket KA-FB007 (26.AAU.KS)
Bracket set without fastening materials, these are provided by Jet Brakel Aero®.
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS032-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.287	KA-TW-BS033-VFO - for Hueck® 1.0
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 1.0;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB006 (26.ABH.KS)
1x Frame bracket KA-FB010 (26.ABX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS033-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.288	KA-TW-BS034-VFO - for Hueck® 85E
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB008 (26.ABP.KS)
1x Frame bracket KA-FB005 (26.AAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS034-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.289	KA-TW-BS035-VFO - for Aluprof® MB-SR50 + Technal® MX
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-SR50, Technal® MX;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB009 (26.ABW.KS)
1x Frame bracket KA-FB010 (26.ABX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS035-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.290	KA-TW-BS064-VFO - for Schüco® AWS 57 RO
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 RO;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB010 (26.ADW.KS)
1x Frame bracket KA-FB013 (26.ADX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS064-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.291	KA-TW-BS081-VFO - for Reynaers® Flush Roof Vent
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB002 (26.AAS.KS)
1x Frame bracket KA-FB005 (26.AAN.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS081-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.292	KA-TW-BS091-VFO - for Heroal® 180ES
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180ES;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB001 (26.AAA.KS)
1x Frame bracket KA-FB018 (26.AFT.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS091-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.293	KA-TW-BS097-VFO - for Aluprof® MB-RW
KA Konsolensatz,bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB002 (26.AAS.KS)
1x Frame bracket KA-FB019 (26.AGC.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS097-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.294	KA-TW-BS100-VFO - for Raico® FRAME+ 100/120RI
KA bracket set, mounted installation, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB015 (26.AGF.KS)
1x Frame bracket KA-FB020 (26.AGE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS100-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.295	KA-TW-BS102-VFO - for Raico® FRAME+ 100/120RI-T
KA bracket set, mounted installation, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB016 (26.AGP.KS)
1x Frame bracket KA-FB021 (26.AGQ.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS102-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.296	KA-BS006-VFO - for Gutmann® S70 SK, Raico® WING 50 SK-R
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70 SK, Raico® WING 50 SK-R;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB001 (26.AAA.KS)
1x Frame bracket KA-FB001 (26.AAD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS006-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AAY.KS

1.1.297	KA-BS036-VFO - for Reynaers® CS 59, CS 68, CS 77, CS 86-HI, Eco + Schüco® AWS 65, AWS 70, AWS 75
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Reynaers® CS 59, CS68, CS 77, CS 86-HI, Eco und Schüco® AWS 65, AWS 70, AWS 75;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB013 (26.AEK.KS)
1x Frame bracket KA-FB012 (26.ACR.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS036-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ACS.KS

1.1.298	KA-BS074-VFO - for Sapa® SFB 1074
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Sapa® SFB 1074;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB013 (26.AEK.KS)
1x Frame bracket KA-FB016 (26.AFA.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS074-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.299	KA-BS076-VFO - for Aluprof® MB 59 Casement
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB 59 Casement;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB002 (26.AAS.KS)
1x Frame bracket KA-FB015 (26.AEX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS076-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AEY.KS

1.1.300	KA-BS077-VFO - for Skandinaviska® SGS
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Skandinaviska® SGS;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set without fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS077-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.301	KA-TW-BS039-VFO - for Reynaers® CS 59, CS 68, CS 77, CS 86-HI, Eco + Schüco® AWS 65, AWS 70, AWS 75
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Reynaers® CS 59, CS68, CS 77, CS 86-HI, Eco und Schüco® AWS 65, AWS 70, AWS 75;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB013 (26.AEK.KS)
1x Frame bracket KA-FB012 (26.ACR.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS039-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ACV.KS

1.1.302	KA-TW-BS071-VFO - for Colt® Kameleon E
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB012 (26.AEE.KS)
1x Frame bracket KA-FB010 (26.ABX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS071-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.303	KA-TW-BS078-VFO - for Skandinaviska® SGS
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Skandinaviska® SGS;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 EV1
 
Frame bracket
Material: Stainless steel A2
Surface: Tumbled
 
Scope of supply:
Bracket set without fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS078-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.304	KA-TW-BS079-VFO - for Aluprof® MB 59 Casement
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB 59 Casement;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB002 (26.AAS.KS)
1x Frame bracket KA-FB015 (26.AEX.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS079-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.305	KA-BS092-VFI - for Raico® FRAME+ 75 und 90 WI
KA bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA drives on outward opening bottom-hung and side-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 und 90 WI;
Minimum space requiered on the window frame 46 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: KA-BS092-VFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFW.KS

1.1.306	KA-BS094-VSI - for Raico® FRAME+ 75 und 75 WI
KA bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA drives on outward opening bottom-hung and side-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75 und 75 WI;
Minimum space requiered on the window frame 30 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: KA-BS094-VSI
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.307	KA-BS085-VFIS - for Reynaers® CS 59, CS 68, CS 77, CS 86-HI + Schüco® AWS 65, AWS 70, AWS 75
KA bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA drives on outward opening side-hung vent windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Reynaers® CS 59, CS 68, CS 77, CS 86-HI; Schüco® AWS 65, AWS 70, AWS 75;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: KA-BS085-VFIS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFL.KS

1.1.308	KA-TW-BS086-VFIS - for Reynaers® CS 59, CS 68, CS 77, CS 86-HI + Schüco® AWS 65, AWS 70, AWS 75
KA-TW bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening side-hung vent windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Reynaers® CS 59, CS 68, CS 77, CS 86-HI; Schüco® AWS 65, AWS 70, AWS 75;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS086-VFIS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFM.KS

1.1.309	KA-BS001-VFO - for Schüco® AWS 102 SK (339 470)
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 102 SK (339 470);
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Schüco®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB001 (26.AAA.KS)
1x Frame bracket KA-FB002 (26.AAB.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS001-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AAF.KS

1.1.310	KA-BS051-VFO - for Schüco® AWS 102 SK (339 490)
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 102 SK (339 490);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB011 (26.ADH.KS)
1x Frame bracket KA-FB002 (26.AAB.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS051-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.311	KA-BS075-VFO - for Reynaers® CW 50
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® CW 50;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket KA-SB014 (26.AEL.KS)
1x Frame bracket KA-FB014 (26.AEM.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-BS075-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AEN.KS

1.1.312	KA-BS093-VFO - for Raico® FRAME+ 75
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 75;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: KA-BS093-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFX.KS

1.1.313	KA-TW-BS045-VFO - for Schüco® AWS 102 SK (339 470)
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 102 SK (339 470);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB001 (26.AAA.KS)
1x Frame bracket KA-FB002 (26.AAB.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS045-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.314	KA-TW-BS068-VFO - for Schüco® AWS 102 SK (339 490)
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 102 SK (339 490);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB011 (26.ADH.KS)
1x Frame bracket KA-FB002 (26.AAB.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS068-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.315	KA-TW-BS073-VFO - for Gutmann® S70 SK und Raico® WING 50 SK-R
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening projected top-hung windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Gutmann® S70 SK und Raico® WING 50 SK-R;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Powder coated
Colour: White aluminium (~ RAL 9006)
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket KA-SB001 (26.AAA.KS)
1x Frame bracket KA-FB001 (26.AAD.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS073-VFO
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.316	KA-BS040-VSI - universal
KA bracket set, mounted installation on the sash, inward opening
 
Performance features:
For mounted installation of KA drives on inward opening windows;
Minimum space requiered on the window frame 30 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-BS040-VSI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ACW.KS

1.1.317	KA-BS046-VFI - universal
KA bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA drives on inward opening windows;
Minimum space requiered on the window frame 46 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-BS046-VFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ADC.KS

1.1.318	KA-BS059-VFI - universal
KA bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA drives on inward opening windows;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-BS059-VFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ADT.KS

1.1.319	KA-BS083-VFIS - universal
KA bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA drives on inward opening windows;
Minimum space requiered on the window frame 45 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-BS083-VFIS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFJ.KS

1.1.320	KA-BS088-VSIS - universal
KA bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA drives on inward opening side-hung vent windows;
Minimum space requiered on the window frame 45 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-BS088-VSIS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFR.KS

1.1.321	KA-TW-BS041-VSI - universal
KA-TW bracket set, mounted installation on the sash, inward opening
 
Performance features:
For mounted installation of KA-TW drives on inward opening windows;
Minimum space requiered on the window frame 30 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS041-VSI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ACX.KS

1.1.322	KA-TW-BS047-VFI - universal
KA-TW bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA-TW drives on inward opening windows;
Minimum space requiered on the window frame 46 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS047-VFI
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ADD.KS

1.1.323	KA-TW-BS084-VFIS - universal
KA-TW bracket set, mounted installation on the window frame, inward opening
 
Performance features:
For mounted installation of KA-TW drives on inward opening side-hung vent windows;
Installation left or right;
Minimum space requiered on the window frame 45 mm;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS084-VFIS
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.AFK.KS

1.1.324	KA-BS050-VFO - universal
KA bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA drives on outward opening façade windows;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-BS050-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ADG.KS

1.1.325	KA-TW-BS052-VFO - universal
KA-TW bracket set, mounted installation on the window frame, outward opening
 
Performance features:
For mounted installation of KA-TW drives on outward opening façade windows;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Aluminium
Surface: Anodized E6 / EV1
 
Frame bracket
Material: V2A stainless steel
 
Scope of supply:
Bracket set without fastening materials.
 
Brand: D+H Mechatronic AG
Type: KA-TW-BS052-VFO
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.ADP.KS

1.1.326	LKJ-KA - for skylight type Jet®
KA bracket set
 
Performance features:
For KA chain drives on Jet® skylights;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V4A stainless steel
 
Adapter Jet skylight
Surface: Anodized
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: LKJ-KA
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 21.051.70

1.1.327	LKK-KA - for skylight type Kleen®
KA bracket set
 
Performance features:
For KA chain drives on Kleen® skylights;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V4A stainless steel
 
Adapter Kleen skylight
Surface: Anodized
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: LKK-KA
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 21.050.60

1.1.328	LKL-KA - for skylight type Lamilux®
KA bracket set
 
Performance features:
For KA chain drives on Lamilux® skylights;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V4A stainless steel
 
Adapter Lamilux skylight
Material: V4A stainless steel
Surface: Anodized
Colour: White aluminium (~ RAL 9006)
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: LKL-KA
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 21.052.50

Information Selection Guide

Technologie LIGHT (K)
LIGHT actuators (230 V AC) can only be controlled in OPEN and CLOSE direction.
 
 
Technologie PLP
Data transmission via the drive‘s connection cable. Drive characteristics can be programmed directly via the supply cable. Thus, no additional cable is required for parameterisation.
 
 
Technologie BSY+
BSY+ enables communication and synchronisation between different components in the window. For example between the chain drives, during synchronous operation, or between window and locking drives (e.g. FRA 11 BSY+ or VLD-BSY+). 
 
 
Technologie ACB
Enables direct bus communication between the controller and the drive for, for example, control with perfect positioning or drive feedback. Communication is via the open source Modbus protocol, and it enables the drive to be combined with an ACB?capable control panel or enables it to be directly connected to higher-level controllers such as a building management system.
1.1.329	PLP chain drive - CDM-1000-0600-1-PLP
24 V DC / 2 A / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
 
The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 600 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 11.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0600-1-PLP
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.201.06

1.1.330	PLP chain drive - CDM-1000-0800-1-PLP
24 V DC / 2.5 A / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
 
The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 800 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 671 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0800-1-PLP
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.201.08

1.1.331	PLP chain drive - CDM-1000-1000-1-PLP
24 V DC / 3 A / 1000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
 
The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 3 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 1000 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 18.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 735 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-01000-1-PLP
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.201.10

1.1.332	PLP chain drive - CDM-1-PLP - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
 
The drive is equipped with motor electronics controlled via microprocessor. Drive functions and performance features are individually programmable via Powerline (PLP) and the D+H software SCS. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 300 mm - 1300 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 
11,5 mm/s (with 500 + 600 mm stroke)
15 mm/s (with 700 + 800 mm stroke)
18,5 mm/s (with 1000 mm stroke)
22,5 mm/s (with 1100 + 1200 + 1300 mm stroke)
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608-841 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1-PLP
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.201.00

1.1.333	Extension functions CDM-1-PLP
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.334	BSY+ chain drive - CDM-5-BSY+ - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 300 mm - 1300 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV:
11,5 mm/s (with 500 + 600 mm stroke)
15 mm/s (with 700 + 800 mm stroke)
18,5 mm/s (with 1000 mm stroke)
22,5 mm/s (with 1100 + 1200 + 1300 mm stroke)
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608-841 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-5-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.204.00

1.1.335	Extension functions CDM-5-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED"
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.336	ACB chain drive - CDM-1000-0600-1-ACB M1
24 V DC / 2 A / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 600 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 11.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0600-1-ACB M1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.11

1.1.337	ACB chain drive - CDM-1000-0600-1-ACB M2
24 V DC / 2 A / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 600 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 11.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0600-1-ACB M2
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.12

1.1.338	ACB chain drive - CDM-1000-0600-1-ACB S1
24 V DC / 2 A / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 600 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 11.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0600-1-ACB S1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.13

1.1.339	ACB chain drive - CDM-1000-0800-1-ACB M1
24 V DC / 2.5 A / 1000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 800 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 671 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0800-1-ACB M1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.21

1.1.340	ACB chain drive - CDM-1000-0800-1-ACB M2
24 V DC / 2.5 A / 1000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 800 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 671 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0800-1-ACB M2
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.22

1.1.341	ACB chain drive - CDM-1000-0800-1-ACB S1
24 V DC / 2.5 A / 1000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2.5 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 800 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 671 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0800-1-ACB S1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.23

1.1.342	ACB chain drive - CDM-1000-1000-1-ACB M1
24 V DC / 3 A / 1000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 3 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 1000 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 18.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 735 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-1000-1-ACB M1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.31

1.1.343	ACB chain drive - CDM-1000-1000-1-ACB M2
24 V DC / 3 A / 1000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 3 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 1000 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 18.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 735 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-1000-1-ACB M2
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.32

1.1.344	ACB chain drive - CDM-1000-1000-1-ACB S1
24 V DC / 3 A / 1000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 3 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 1000 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 18.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 735 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-1000-1-ACB S1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.33

1.1.345	ACB chain drive - CDM-1-ACB - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Low wiring effort with an option of looping in up to 2 drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 2 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 300 mm - 1300 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 
11,5 mm/s (with 500 + 600 mm stroke)
15 mm/s (with 700 + 800 mm stroke)
18,5 mm/s (with 1000 mm stroke)
22,5 mm/s (with 1100 + 1200 + 1300 mm stroke)
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608-841 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1-PLP
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.200.00

1.1.346	Extension functions CDM-1-ACB
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA" -End position message "switch OPEN"
	Option "SZ" -End position message "switch CLOSED"
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.347	ACB chain drive - CDM-1000-0600-5-ACB M1
230 V AC / 85 VA / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 600 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 11.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0600-5-ACB M1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.11

1.1.348	ACB chain drive - CDM-1000-0600-5-ACB M2
230 V AC / 85 VA / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 600 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 11.5 mm/s
CLOSED running speed: 5 mm/s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0600-5-ACB M2
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.12

1.1.349	ACB chain drive - CDM-1000-0600-5-ACB S1
230 V AC / 85 VA / 1000 N / 600 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 600 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 11.5 mm/s
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0600-5-ACB S1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.13

1.1.350	ACB chain drive - CDM-1000-0800-5-ACB M1
230 V AC / 85 VA / 1000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 800 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 671 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0800-5-ACB M1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.21

1.1.351	ACB chain drive - CDM-1000-0800-5-ACB M2
230 V AC / 85 VA / 1000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 800 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 671 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0800-5-ACB M2
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.22

1.1.352	ACB chain drive - CDM-1000-0800-5-ACB S1
230 V AC / 85 VA / 1000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 800 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 15 mm/s
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 671 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-0800-5-ACB S1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.23

1.1.353	ACB chain drive - CDM-1000-1000-5-ACB M1
230 V AC / 85 VA / 1000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 1000 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 18.5 mm/s
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 735 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-1000-5-ACB M1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.31

1.1.354	ACB chain drive - CDM-1000-1000-5-ACB M2
230 V AC / 85 VA / 1000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main 2
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 1000 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 18.5 mm/s
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 735 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-1000-5-ACB M2
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.32

1.1.355	ACB chain drive - CDM-1000-1000-5-ACB S1
230 V AC / 85 VA / 1000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Sub 1
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 1000 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 18.5 mm/s
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: Powder-coated
Colour: White aluminium (~ RAL 9006)
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 735 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-1000-1000-5-ACB S1
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.33

1.1.356	ACB chain drive - CDM-5-ACB - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Can be combined with all D+H locking drives.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with microprocessor-controlled motor and synchronous electronic BSY+ for a precise synchronous running of four drives. Drive functions and performance features are individually programmable via the D+H software SCS. Integrated ACB (Advanced Communication Bus) BUS interface with ModBus protocol. Direct integration via open BUS communication through the ACB (Advanced Communication Bus), e.g. in a building management system (building automation). High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design. 
 
A multi-stage anti-trap protection system (runtime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Configuration: Main or Sub
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 300 mm - 1300 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV: 
11,5 mm/s (with 500 + 600 mm stroke)
15 mm/s (with 700 + 800 mm stroke)
18,5 mm/s (with 1000 mm stroke)
22,5 mm/s (with 1100 + 1200 + 1300 mm stroke)
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608-841 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-5-ACB
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.202.00

1.1.357	Extension functions CDM-5-ACB
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.358	Chain drive - CDM-5 - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile.
Drive for electromotive opening and closing of extremely heavy windows and flaps in façade and roof areas.
Control takes place directly via a mains voltage range of 120 - 230 V AC.
 
The drive is equipped with motor electronics controlled via microprocessor. Stroke programming can be carried out using magnets. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Low operating noises thanks to the innovative acoustic decoupling of the drive components. Use of a wear-free brushless motor with high efficiency. The drive is available with special chain stabilisation with corrosion protection and lifetime lubrication. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to compact design.
 
A multi-stage anti-trap protection system (runrime, force/power, stroke) comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. Easy installation thanks to s polarity reversal protection connector system.
 
Technical data:
Operating voltage: 120 - 230 V AC / +10/-10 % / 50 - 60 Hz
Performance: 80 W / 85 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Shutdown: Integrated electronic load cut-off
Force of pressure: 1000 N (note pressure load diagram)
Tensile force: 1000 N
Nominal locking force: 3500 N
Service life: 20000 double strokes
Stroke length: 300 mm - 1300 mm / ±2 %
OPEN running speed: 7 mm/s
OPEN running speed - SHEV:
11,5 mm/s (with 500 + 600 mm stroke)
15 mm/s (with 700 + 800 mm stroke)
18,5 mm/s (with 1000 mm stroke)
22,5 mm/s (with 1100 + 1200 + 1300 mm stroke)
CLOSED running speed: 5 mm/ s
Type of protection: IP 42
Emission sound pressure level: LpA ≤ 45 dB(A)
Temperature range: -15 °C till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium
Surface: on request
Colour: on request
Connection: Silicone cable (must be ordered separately)
Dimensions (WxHxD): 608-841 x 53 x 90 mm
 
Scope of supply:
Drive unit, instruction for use
The drive is supplied without connection cable.
Pre-assembled silicone cables with connector plugs must be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-5
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.203.00

1.1.359	Extension functions CDM-5
	Option "HP" -Stroke programming
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.360	CDM-FB001 - universal
CDM universal frame bracket, mounted installation 
 
Performance features:
For mounted installation of CDM drives on outward opening windows.
Suitable for the Raico Frame+ 100/120 RI profile, among others.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Frame bracket without fasteners..
Fasteners can be ordered separately.
 
Attention: Additional washers and fastening materials may be required for these brackets. Please contact your D+H partner for this.
 
Brand: D+H Mechatronic AG
Type: CDM-FB001
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 22.998.01

1.1.361	CDM-FB002 - universal
CDM universal frame bracket, mounted installation 
 
Performance features:
For mounted installation of CDM drives on outward opening windows.
Suitable for the Raico Frame+ 75WA profile, among others.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Frame bracket without fasteners..
Fasteners can be ordered separately.
 
Attention: Additional washers and fastening materials may be required for these brackets. Please contact your D+H partner for this.
 
Brand: D+H Mechatronic AG
Type: CDM-FB002
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 22.998.01

1.1.362	CDM-SB001 - universal
CDM sash bracket angled, mounted installation
 
Performance features:
For mounted installation of CDM drives on outward opening windows.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Sash bracket without fasteners..
Fasteners can be ordered separately.
 
Attention: Additional washers and fastening materials may be required for these brackets. Please contact your D+H partner for this.
 
Brand: D+H Mechatronic AG
Type: CDM-SB001
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 22.998.09

1.1.363	CDM-SB002 - universal
CDM sash bracket, mounted installation
 
Performance features:
For mounted installation of CDM drives on outward opening windows.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Sash bracket without fasteners..
Fasteners can be ordered separately.
 
Attention: Additional washers and fastening materials may be required for these brackets. Please contact your D+H partner for this.
 
Brand: D+H Mechatronic AG
Type: CDM-SB002
 
Planning Support (https://www.dh-partner.com/de/de/leistungen/beratung-und-planungsunterstuetzung)

Unit : Stk
Artikelnr. : 22.998.11

1.1.364	CDM-FB001 + CDM-SB001 - for Raico® FRAME+ 100/120RI + WING 105
CDM Rahmen- und Flügelkonsole, aufgesetzte Montage 
 
Performance features:
For mounted installation of CDM drives on outward opening windows. 
Optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI + WING 105.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Frame bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Sash bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Washer:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Frame and sash bracket without fasteners.
Fasteners can be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-FB001 + CDM-SB001 + Add Pack CDM-01
 
Planning Support (https://www.dh-partner.com/de/de/leistungen/beratung-und-planungsunterstuetzung)

Unit : Stk
Artikelnr. : 22.998.01 + 22.998.09 + 22.998.13

1.1.365	CDM-FB001 + CDM-SB001 - for Schüco® AW RO 50
CDM Rahmen- und Flügelkonsole, aufgesetzte Montage 
 
Performance features:
For mounted installation of CDM drives on outward opening windows. 
Optimised for installation on the window profile of the profile manufacturer: Schüco® AW RO 50.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Frame bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Sash bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Washer:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Frame and sash bracket without fasteners.
Fasteners can be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-FB001 + CDM-SB001 + Add Pack CDM-04 + Add Pack CDM-05
 
Planning Support (https://www.dh-partner.com/de/de/leistungen/beratung-und-planungsunterstuetzung)

Unit : Stk
Artikelnr. : 22.998.01 + 22.998.09 + 22.998.19 + 22.998.21

1.1.366	CDM-FB001 + CDM-SB002 - for Reynaers® Attic Window
CDM Rahmen- und Flügelkonsole, aufgesetzte Montage 
 
Performance features:
For mounted installation of CDM drives on outward opening windows. 
Optimised for installation on the window profile of the profile manufacturer: Reynaers® Attic Window.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Frame bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Sash bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Frame and sash bracket without fasteners.
Fasteners can be ordered separately.
 
Brand: D+H Mechatronic AG
Type: CDM-FB001 + CDM-SB002
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 22.998.01 + 22.998.11

1.1.367	CDM-FB001 + CDM-SB001 - for Wicona® Roof + Wictec 50/60
CDM Rahmen- und Flügelkonsole, aufgesetzte Montage 
 
Performance features:
For mounted installation of CDM drives on outward opening windows. 
Optimised for installation on the window profile of the profile manufacturer: Wicona® Roof + Wictec 50/60.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Frame bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Sash bracket:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Washer:
Material: Stainless steel A2
Surface: Bare / tumbled
 
Scope of supply:
Frame and sash bracket without fasteners.
Fasteners can be ordered separately.
 
Brand: D+H Mechatronic AGG
Type: CDM-FB001 + CDM-SB001 + 2x Add Pack CDM-05
 
Planning Support (https://www.dh-partner.com/de/de/leistungen/beratung-und-planungsunterstuetzung)

Unit : Stk
Artikelnr. : 22.998.01 + 22.998.09 + 22.998.21

Information Selection Guide

Technologie BSY+
BSY+ enables communication and synchronisation between different components in the window. For example between the chain drives, during synchronous operation, or between window and locking drives (e.g. FRA 11 BSY+ or VLD-BSY+). 
1.1.368	BSY+ High-performance chain drive - CDP 1500/800-BSY+
24 V DC / 4 A / 1500 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N
(note pressure load diagram)
Tensile force: 1000 N
Nominal locking force *: 3000 N
Service life: > 10000 double strokes
Stroke length: 800 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 807 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP 1500/800-BSY+
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.600.10

1.1.369	BSY+ High-performance chain drive - CDP 1500/1000-BSY+
24 V DC / 4 A / 1500 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 4 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N
(note pressure load diagram)
Tensile force: 1000 N
Nominal locking force *: 3000 N
Service life: > 10000 double strokes
Stroke length: 1000 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 934 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP 1500/1000-BSY+
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.600.15

1.1.370	BSY+ High-performance chain drive - CDP-BSY+ - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right.
 
Technical data:
(per drive)
Operating voltage: 24 V DC / ±15 %
Current consumption:
3 A (CDP 800-BSY+)
3.3 A (CDP 1000-BSY+)
4 A (CDP 1500-BSY+)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main or Sub
Design: Symmetric
Force of pressure:
800 N (CDP 800-BSY+)
1000 N (CDP 1000-BSY+)
1500 N (CDP 1500-BSY+)
(note pressure load diagram)
Tensile force:
800 N (CDP 800-BSY+)
1000 N (CDP 1000-BSY+)
1000 N (CDP 1500-BSY+)
Nominal locking force *: 3000 N
Service life: > 10000 double strokes
Stroke length: 600 mm - 1500 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: on request
Connection: Silicone cable
Dimensions (WxHxD): 702-1264 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.600.00

1.1.371	Extension functions CDP-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "DS" -Loop-through option enables connection with one additional D+H drive
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.372	BSY+ High-performance chain drive - CDP 1500/800-K-BSY+
230 V AC / 107 VA / 1500 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / ±10 % / 50 Hz
Performance: 80 W / 107 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N
(note pressure load diagram)
Tensile force: 1000 N
Nominal locking force *: 3000 N
Service life: > 10000 double strokes
Stroke length: 800 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 807 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: 1500/800-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.373	BSY+ High-performance chain drive - CDP 1500/1000-K-BSY+
230 V AC / 107 VA / 1500 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / ±10 % / 50 Hz
Performance: 80 W / 107 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N
(note pressure load diagram)
Tensile force: 1000 N
Nominal locking force *: 3000 N
Service life: > 10000 double strokes
Stroke length: 1000 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 934 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Typ: 1500/1000-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.374	BSY+ High-performance chain drive - CDP-K-BSY+ - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right. Direct control via 230 V AC.
 
Technical data:
(per drive)
Operating voltage: 230 V AC / ±10 % / 50 Hz
Performance:
50 W / 71 VA (CDP 800-K-BSY+)
60 W / 80 VA (CDP 1000-K-BSY+)
80 W / 107 VA (CDP 1500-K-BSY+)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Configuration: Main or Sub
Design: Symmetric
Force of pressure:
800 N (CDP 800-K-BSY+)
1000 N (CDP 1000-K-BSY+)
1500 N (CDP 1500-K-BSY+)
(note pressure load diagram)
Tensile force:
800 N (CDP 800-K-BSY+)
1000 N (CDP 1000-K-BSY+)
1000 N (CDP 1500-K-BSY+)
Nominal locking force *: 3000 N
Service life: > 10000 double strokes
Stroke length: 600 mm - 1500 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: on request
Connection: Silicone cable
Dimensions (WxHxD): 807-1264 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.602.00

1.1.375	Extension functions CDP-K-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.376	BSY+ High-performance chain drive - CDP-TW-3000/800-BSY+
24 V DC / 8 A / 3000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 3000 N
(note pressure load diagram)
Tensile force: 2000 N
Nominal locking force *: 6000 N
Service life: > 10000 double strokes
Stroke length: 800 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 1672 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-TW 3000/800-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.377	BSY+ High-performance chain drive - CDP-TW-3000/1000-BSY+
24 V DC / 8 A / 3000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption: 8 A
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 3000 N
(note pressure load diagram)
Tensile force: 2000 N
Nominal locking force *: 6000 N
Service life: > 10000 double strokes
Stroke length: 1000 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 1672 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-TW-3000/1000-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.378	BSY+ High-performance chain drive - CDP-TW-BSY+ - freely configurable
24 V DC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right.
 
Technical data:
Operating voltage: 24 V DC / ±15 %
Current consumption:
6 A (CDP-TW 1600-BSY+)
6.6 A (CDP-TW 2000-BSY+)
8 A (CDP-TW 3000-BSY+)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
1600 N (CDP-TW 1600-BSY+)
2000 N (CDP-TW 2000-BSY+)
3000 N (CDP-TW 3000-BSY+)
(note pressure load diagram)
Tensile force:
1600 N (CDP-TW 1600-BSY+)
2000 N (CDP-TW 2000-BSY+)
2000 N (CDP-TW 3000-BSY+)
Nominal locking force *: 6000 N
Service life: > 10000 double strokes
Stroke length: 800 mm - 1500 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: on request
Connection: Silicone cable
Dimensions (WxHxD): 1672/2002 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.601.00

1.1.379	Extension functions CDP-TW-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "VP" -Signal programming for connection with D+H BSY+ locking drives
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SKS" -Direct connection of an anti-pitch strip or an optical sensor for closing edge monitoring at the drive possible
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.380	BSY+ High-performance chain drive - CDP-TW-3000/800-K-BSY+
230 V AC / 214 VA / 3000 N / 800 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / ±10 % / 50 Hz
Performance: 160 W / 214 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N
(note pressure load diagram)
Tensile force: 1000 N
Nominal locking force *: 6000 N
Service life: > 10000 double strokes
Stroke length: 800 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 1672 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-TW-3000/800-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.381	BSY+ High-performance chain drive - CDP-TW-3000/1000-K-BSY+
230 V AC / 214 VA / 3000 N / 1000 mm stroke
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / ±10 % / 50 Hz
Performance: 160 W / 214 VA
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure: 1500 N
(note pressure load diagram)
Tensile force: 1000 N
Nominal locking force *: 6000 N
Service life: > 10000 double strokes
Stroke length: 1000 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: White aluminium (~ RAL 9006)
Connection: 2.5 m silicone cable
Dimensions (WxHxD): 1672 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with 2.5 m silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-TW-3000/1000-K-BSY+
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)l

Unit : Stk

1.1.382	BSY+ High-performance chain drive - CDP-TW-K-BSY+ - freely configurable
230 V AC / Special production according to customer requirements
 
Performance features:
Electromotive drive unit for mounting on the window frame profile. Drive for electromotive opening and closing of extremely heavy windows and flaps. The drive is equipped with motor electronics controlled via microprocessor BSY+ for precise synchronous operation one window element. Drive chain with symmetrical chain outlet for easy installation and an appealing design due to narrow construction. Synchronisation of up to 4 drives via microprocessor-controlled BSY+ technology is possible. Drive functions and performance features are individually programmable via the D+H software SCS. Can be used for openings for smoke exhaust; D+H Euro SHEV in accordance with EN 12101-2; and for daily ventilation. High-speed function (HS) for especially fast opening windows in case of fire (SHEV). Particularly quiet drive in daily ventilation mode. A multi-stage anti-trap protection system comes standard and can be set via the D+H software SCS. In order to reduce the permanent load on the gasket, a relief of pressure on window gasket is performed after the elements have been closed. . Power supply and BSY+ signals can be looped through the drive. The power supply can be connected either from left or right. Direct control via 230 V AC.
 
Technical data:
Operating voltage: 230 V AC / ±10 % / 50 Hz
Performance:
100 W / 142 VA (CDP-TW 1600-K-BSY+)
120 W / 160 VA (CDP-TW 2000-K-BSY+)
160 W / 214 VA (CDP-TW 3000-K-BSY+)
Duty cycle: 30 % (ON: 3 min. / OFF: 7 min.)
Force of pressure:
1600 N (CDP-TW 1600-K-BSY+)
2000 N (CDP-TW 2000-K-BSY+)
3000 N (CDP-TW 3000-K-BSY+)
(note pressure load diagram)
Tensile force:
1600 N (CDP-TW 1600-K-BSY+)
2000 N (CDP-TW 2000-K-BSY+)
2000 N (CDP-TW 3000-K-BSY+)
Nominal locking force *: 6000 N
Service life: > 10000 double strokes
Stroke length: 800 mm - 1500 mm
OPEN running speed: 6 mm/s
OPEN running speed - SHEV: 17.7 mm/s
CLOSED running speed: 6 mm/s
Type of protection: IP 32
Emission sound pressure level: LpA ≤ 70 dB(A)
Temperature range:-15 °C (-5 °C **) till +75 °C
Fire resistance: B300 (30 min / 300 °C)
Housing: Aluminium / Polycarbonate (end cap)
Colour housing: on request
Connection: Silicone cable
Dimensions (WxHxD): 1672/2002 x 67 x 110 mm
 
* Depending on the mounting
** In accordance with VdS 2580
 
Scope of supply:
Drive unit with silicone connection cable, instruction for use
 
Brand: D+H Mechatronic AG
Type: CDP-TW-K-BSY+
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.603.00

1.1.383	Extension functions CDP-TW-K-BSY+
	Option "CP" -Customized drive function programming, e.g. operation speed, force and stroke
	Option "HP" -Stroke programming
	Option "LS" -Low-speed programming in CLOSE direction 5 mm/s
	Option "SA-SZ" -End position message "switch OPEN" und "switch CLOSED"
	Option "AS2" -Acoustic signal according to protection class 2 MaschRL/42/EG
	Option "AS3" -Acoustic signal according to protection class 3 MaschRL/42/EG
	Option "special colour" -Colour coating for perfect integration into façade optics according to RAL, DB, NCS


Unit : Stk

1.1.384	CDP-BS001-OM - for Schüco® AWS 57 (369 780)
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (369 780);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS001-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CAJ.KS

1.1.385	CDP-BS002-OM - for Aluprof® MB-SR50 + Gutmann® S70 Dach + Raico® WING 105D + Technal® MX + Wicona® WICTEC 50/6
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Aluprof® MB-SR50, Gutmann® S70 Dach, Raico® WING 105D, Technal® MX, Wicona® WICTEC 50/60;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB002 (26.CAF.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS002-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CAK.KS

1.1.386	CDP-BS003-OM - for Schüco® AWS 57 (331 820)
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (331 820);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB003 (26.CAG.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS003-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CAL.KS

1.1.387	CDP-BS004-OM - for Reynaers® Flush Roof Vent
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB004 (26.CAH.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS004-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CAM.KS

1.1.388	CDP-BS005-OM - for Hück® 1.0 + Jet-Brakel Aero® Ventria TG + Sapa® SFB 5050
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Hück® 1.0, Jet-Brakel Aero® Ventria TG, Sapa® SFB 5050;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Adapter bracket CDP-AB001 (26.CAB.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS005-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.389	CDP-BS006-OM - for Colt® Kameleon E
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Stainless steel casting
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Adapter bracket CDP-AB002 (26.CAC.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS006-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.390	CDP-BS007-OM - for Heroal® 180
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
Instructions for installation can be found in the D+H application drawings and product information..
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Adapter bracket CDP-AB003 (26.CAD.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS007-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.391	CDP-BS008-OM - for Hueck® 85E
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Stainless steel casting
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
1x Sash bracket CDP-SB001 (26.CAA.KS)
1x Adapter bracket CDP-AB001 (26.CAB.KS)
1x Frame bracket CDP-FB002 (26.CAF.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-BS008-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.392	CDP-BS017-OM - for Raico® Wing 50
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® Wing 50;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Stainless steel casting
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: CDP-BS017-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.393	CDP-BS019-OM - for Raico® WING 105DI
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-BS019-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CAS.KS

1.1.394	CDP-BS021-OM - for Aluprof® MB-RW
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-BS021-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.395	CDP-BS023-OM - for Heroal® C 50 HI
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® C 50 HI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-BS023-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.396	CDP-BS024-OM - for Raico® FRAME+ 100/120RI
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
Der Konsolensatz ist Bestandteil des nach DIN EN 12101-2 geprüften D+H NRWG für die Profilsysteme von Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-BS024-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CBN.KS

1.1.397	CDP-BS026-OM - for Raico® FRAME+ 100RI-T
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-BS026-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CBP.KS

1.1.398	CDP-BS028-OM - for Raico® FRAME+ 120RI-T
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 120RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-BS028-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CBR.KS

1.1.399	CDP-TW-BS009-OM - for Schüco® AWS 57 (369 780)
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (369 780);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS009-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.400	CDP-TW-BS010-OM - for Aluprof® MB-SR50 + Gutmann® S70 Dach + Raico® WING 105D + Technal® MX + Wicona® WICTEC 50/60
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Aluprof® MB-SR50, Gutmann® S70 Dach, Raico® WING 105D, Technal® MX, Wicona® WICTEC 50/60;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB002 (26.CAF.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS010-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CAU.KS

1.1.401	CDP-TW-BS011-OM - for Schüco® AWS 57 (331 820)
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Schüco® AWS 57 (331 820);
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB003 (26.CAG.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS011-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.402	CDP-TW-BS012-OM - for Reynaers® Flush Roof Vent
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Reynaers® Flush Roof Vent;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
1x Frame bracket CDP-FB004 (26.CAH.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS012-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.403	CDP-TW-BS013-OM - for Hück® 1.0, Jet-Brakel Aero® Ventria TG, Sapa® SFB 5050
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturers: Hück® 1.0, Jet-Brakel Aero® Ventria TG, Sapa® SFB 5050;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
2x Adapter bracket CDP-AB001 (26.CAB.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS013-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.404	CDP-TW-BS014-OM - for Colt® Kameleon E
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Colt® Kameleon E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Stainless steel casting
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
2x Adapter bracket CDP-AB002 (26.CAC.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS014-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.405	CDP-TW-BS015-OM - for Heroal® 180
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Heroal® 180;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
2x Adapter bracket CDP-AB003 (26.CAD.KS)
1x Frame bracket CDP-FB001 (26.CAE.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS015-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.406	CDP-TW-BS016-OM - for Hueck® 85E
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Hueck® 85E;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Stainless steel casting
Surface: Sandblasted
 
Adapter bracket
Material: V2A stainless steel
Surface: Tumbled
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Set contents:
2x Sash bracket CDP-SB001 (26.CAA.KS)
2x Adapter bracket CDP-AB001 (26.CAB.KS)
1x Frame bracket CDP-FB002 (26.CAF.KS)
Including all necessary fastening materials
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS016-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.407	CDP-TW-BS018-OM - for Raico® Wing 50
CDP bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® Wing 50;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: Stainless steel casting
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS018-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.408	CDP-TW-BS020-OM - for Raico® WING 105DI
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® WING 105DI;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS020-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CBB.KS

1.1.409	CDP-TW-BS022-OM - for Aluprof® MB-RW
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Aluprof® MB-RW;
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS022-OM
 
The D+H partner on site is at your disposal for design variants.
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk

1.1.410	CDP-TW-BS025-OM - for Raico® FRAME+ 100/120RI
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100/120RI;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS025-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CBO.KS

1.1.411	CDP-TW-BS027-OM - for Raico® FRAME+ 100RI-T
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 100RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS027-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CBQ.KS

1.1.412	CDP-TW-BS029-OM - for Raico® FRAME+ 120RI-T
CDP-TW bracket set, for installation opposite the hinge, outward opening
 
Performance features:
For mounted installation of CDP-TW drives on roof windows;
Bracket set optimised for installation on the window profile of the profile manufacturer: Raico® FRAME+ 120RI-T;
The bracket set is part of the D+H NSHEV system tested according to EN 12101-2 for the profile systems of Raico®.
Instructions for installation can be found in the D+H application drawings and product information.
 
Technical data:
Sash bracket
Material: V2A stainless steel
Surface: Sandblasted
 
Frame bracket
Material: V2A stainless steel
Surface: Tumbled
 
Scope of supply:
Bracket set including all fastening materials for installation.
 
Brand: D+H Mechatronic AG
Type: CDP-TW-BS029-OM
 
Planning Support (https://www.dh-partner.com/int/en/service/planning-support)

Unit : Stk
Artikelnr. : 26.CBS.KS